Buderus Logano G215 WS Скачать руководство пользователя страница 6

Страница: 6 / 62

Product description

Logano G215 WS - We reserve the right to make any changes due to technical modifications.

Product description

This boiler is a low temperature boiler for oil or gas
combustion with modulating boiler water temperature
control.

The boiler comprises:

–

Control device

–

Boiler shell

–

Boiler block with lagging

The control device monitors and controls all electrical
boiler components.

The boiler shell prevents energy losses and acts as a
silencer.

The boiler block transfers the heat generated by the
burner to the heating water. The lagging prevents
energy losses.

Suitable burners

Fit a suitable oil or gas burner to the boiler. Observe the
boiler specifications when selecting a burner
(

Section 3.1, page 7).

Fig. 1

Boiler without burner

Control device

Boiler shell

Boiler block with lagging

Burner door casing

CAUTION!

SYSTEM DAMAGE

through incorrect burner.

Only use burners which meet the
technical boiler requirements.

Содержание Logano G215 WS































































Результаты поиска

Содержание Logano G215 WS

Отзывы:

Похожие инструкции для Logano G215 WS

Бренды по названию

Популярные бренды

Buderus Logano G215 WS, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Logano G215 WS

Отзывы:

Похожие инструкции для Logano G215 WS

Бренды по названию

Популярные бренды