Austin Kontore Crestview Chicken Coop Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 54

background image

© 2009 Austin Kontore LLC

Page 49 of 54

Door Testing

(1) 22” Panel Door Unit
(fabricated earlier)

(2) 19” Screen Door Units
(fabricated earlier)

The three doors were fitted earlier during the installation of the Door Slide Rails. In this section, the door
action will be tested and any problems worked through.

Slide the three doors into the Door Rails. There are two lower Screen doors, measuring 19” high
and one upper Panel Door measuring 22” high. One side of the unit has two doors: Panel on the
top, Screen on the bottom. The opposite side of the unit has one door: Screen on the bottom.

The doors should slide easily on the Door Rails. You should be able to open the doors from either
direction (sliding left or right).

Important:

Do not force the doors if they do not slide easily. Instead, follow the below

instructions to determine the source of the problem.

«
...
47
48
49
50
51
...
»

Содержание Crestview Chicken Coop























































Отзывы:

Нет отзывов

Похожие инструкции для Crestview Chicken Coop

Бренд: Rabe Страницы: 65

Бренд: Idmed Страницы: 2

Бренд: Yamaha Страницы: 48

Бренд: VelociRAX Страницы: 4

Бренд: ABM Страницы: 17

Бренд: Vaisala Страницы: 2

Pendalyte 40472U

Бренд: Lightolier Страницы: 3

Бренд: Kelso Страницы: 21

PRO-FORM ab GLIDER

Бренд: ICON Health & Fitness Страницы: 16

Бренд: ABB Страницы: 136

Бренд: ABB Страницы: 108

Бренд: Beckman Coulter Страницы: 52

Бренд: Copernicus Страницы: 13

Бренд: MD SPORTS Страницы: 15

Бренд: Sweet Sound Electronics Страницы: 6

Бренд: Richiger Страницы: 76

Be strong NS 200X

Бренд: Nautilus Страницы: 27

Бренд: ADJ Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды