Austin Kontore Crestview Chicken Coop Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 54

background image

© 2009 Austin Kontore LLC

Page 7 of 54

Master Checklist

Use the Master Checklist to keep track of your overall progress.

It’s a good idea to pull out these next three pages and use them to monitor your progress.

Build (2) 20 ½” fixed panel units for the upper level.

These make up the two solid sides of the coop.

Build (1) 22” door panel unit for the upper level.

This is the upper solid door.

Build (1) 20 ½” fixed screen unit for the upper level.

This is the screen opening for the upper level.

Build (2) 17” fixed screen units for the lower level.

These two screens are for the lower part of the coop and
do not open.

Build (2) 19” door screen units for the lower level.

These lower screen doors allow access to chicken runs,
and allow for food and water replenishment.

«
...
5
6
7
8
9
...
»

Содержание Crestview Chicken Coop























































Отзывы:

Нет отзывов

Похожие инструкции для Crestview Chicken Coop

Бренд: ICP DAS USA Страницы: 45

Бренд: Parker Страницы: 64

Бренд: Parker Страницы: 40

Matrx Digital MDM

Бренд: Parker Страницы: 20

Бренд: York International Страницы: 16

Бренд: X-10 Страницы: 12

Бренд: Equinox Systems Страницы: 8

Бренд: Poulan Pro Страницы: 17

Бренд: Unika Страницы: 8

Бренд: Parkside Страницы: 37

Бренд: PALAZZANI Страницы: 131

VEX-WPCR Series

Бренд: Exitronix Страницы: 4

ADVANTAGE 78400-117

Бренд: Medivators Страницы: 12

CAPE HORN EC202B

Бренд: SMP Playgrounds Страницы: 22

INTIMIDATOR 15XPC

Бренд: Bandit Страницы: 112

Бренд: König Electronic Страницы: 100

Бренд: ParaBody Страницы: 15

Бренд: ParaBody Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды