Austin Kontore Crestview Chicken Coop Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 54

background image

© 2009 Austin Kontore LLC

Page 22 of 54

Staple out from the center, placing staples about 3” apart.

Important:

Make sure to keep mesh flat and taut

while stapling.

Staple down the sides and corners.

Use enough staples to keep the Hardware Cloth securely
mounted to the frame.

Insert three ¾” Lathe screws (finger tight) into each 17”
pieces of pre-drilled weather stripping.

Align the 17” piece of weather stripping to the edge of the
door assembly. The edge of the weather stripping should
be flush with the edge of the door.

Optional:

When attaching the weather stripping you can

apply a thin coat of glue between the wooden strip and
the door. The glue will augment the three Lathe screws to
provide additional strength.

Make sure that the 17” piece of weather stripping is
equally spaced between the top and bottom edges of the
door.

There should be about 1” of space between the
top/bottom edge of the door and the strip.

«
...
20
21
22
23
24
...
»

Содержание Crestview Chicken Coop























































Отзывы:

Нет отзывов

Похожие инструкции для Crestview Chicken Coop

Бренд: ParaBody Страницы: 5

Бренд: Sagola Страницы: 20

Бренд: Earmor Страницы: 5

Бренд: Gaspardo Страницы: 196

Бренд: RAB Страницы: 2

Бренд: Nitecore Страницы: 4

Бренд: Pablo Страницы: 7

Synthesis SDEC-3000

Бренд: JBL Страницы: 24

Бренд: Xilica Audio Design Страницы: 30

Бренд: Pari Страницы: 12

Бренд: laerdal Страницы: 2

Бренд: laerdal Страницы: 104

Бренд: laerdal Страницы: 33

Бренд: laguna Страницы: 16

Бренд: Lafayette Страницы: 2

Бренд: Launch Страницы: 3

Бренд: Launch Страницы: 43

Бренд: Launch Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды