Austin Kontore Crestview Chicken Coop Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 54

background image

© 2009 Austin Kontore LLC

Page 32 of 54

Core Structure:
Upper Level

(1) 3’ x3’ Core Square
(prefabricated)

(2) 20 ½” Fixed Panel Units

(16) 1 5/8” screws
(to fasten the core)

(8) 1 ¼” screws
(to fasten the fixed panels)

The final portion of the Core is built in this section. The upper level Core Square is installed, along with
the two upper Fixed Panel units. Once this section is complete your coop will really start looking like a
structure!

Place a 20 ½” Fixed Panel Unit (which you assembled earlier) on
top of the Middle Core Square. Clamp to a post so that it
doesn’t fall down.

Important:

The upper Fixed Panel and the lower Fixed

Screen are on the same side of the coop. The Screen makes up
the lower portion of the side, and the Panel makes up the
upper portion of the side.

On the opposite side from the Fixed Panel Unit you just
clamped, place the other 20 ½” Fixed Panel Unit on top of the
Middle Core Square. Clamp it to a post, as you did in the
previous step.

Note:

Having these Fixed Panel Units temporarily held in

place allows you to more easily install the Upper Core Square.

Slide the 3’ x 3’ upper Core Square through the four posts until
it sits on top of the two clamped Fixed Panel Units.

Using a small level, ensure that the Upper Core Square is level.

«
...
30
31
32
33
34
...
»

Содержание Crestview Chicken Coop























































Отзывы:

Нет отзывов

Похожие инструкции для Crestview Chicken Coop

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: K&K Страницы: 8

medialon Showmaster Go

Бренд: 7th Sense Страницы: 9

Бренд: Faderfox Страницы: 8

Бренд: Hagerman Страницы: 4

Бренд: hager Страницы: 2

TECSHOW QUAD SPIDER 60

Бренд: Ampro Страницы: 9

Бренд: LAZBOY Страницы: 9

Бренд: M-Audio Страницы: 3

Web Riderz MM00124 Web Swing

Бренд: M&M Sales Enterprises Страницы: 2

Бренд: Ultimate Healthcare Страницы: 2

Бренд: Ultimate Healthcare Страницы: 40

Бренд: Gaspardo Страницы: 44

Бренд: X-METAL Страницы: 135

Бренд: ABB Страницы: 112

Бренд: Landoll Страницы: 144

Бренд: Castellini Страницы: 299

Бренд: Lowenstein Medical Страницы: 457

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды