Austin Kontore Crestview Chicken Coop Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 54

background image

© 2009 Austin Kontore LLC

Page 45 of 54

Mounting Roof

(1) Roof Unit
(prefabricated)

(4) 2” “L” Brackets

(16) ½” Lathe Screws
(Four per “L” Bracket)

The coop is really coming together, and having the roof in place will help put the finishing touches on. As
the Roof is prefabricated, this process is quite easy to do. Four brackets are installed, and the Roof
Assembly is fastened to the brackets.

If you have placed the Upper Panel Door in place, you should slide it off and put it aside. Having two
sides accessible will make installing the brackets easier.

From the top of the upper Core Square, measure 8” from
edge and align “L” bracket to top edge of the square. The
bracket should be flush.

With the “L” bracket held in place, make two marks for the
pilot holes.

Drill two pilot holes at the marks just made.

Important:

Don’t drill too deep! You don’t want to

drill through the entire thickness of the wood. A hole
about ½” in depth is sufficient. This is a very shallow hole.

Fasten the “L” bracket to the Core Square using two ½”
Lathe screws.

«
...
43
44
45
46
47
...
»

Содержание Crestview Chicken Coop























































Отзывы:

Нет отзывов

Похожие инструкции для Crestview Chicken Coop

Бренд: Raymarine Страницы: 55

Бренд: Halyard Страницы: 4

Underwater Light Show & Fountain

Бренд: GAME Страницы: 2

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренд: M-Triangel Страницы: 6

medialon Showmaster Go

Бренд: 7th Sense Страницы: 9

Бренд: Ultimaker Страницы: 38

Бренд: A&D Страницы: 2

Бренд: A&D Страницы: 176

Бренд: IDEAL Networks Страницы: 10

Бренд: P.Lindberg Страницы: 76

Бренд: TATU Страницы: 30

Бренд: Rane Страницы: 4

Бренд: Sabio Страницы: 182

Бренд: Raytec Страницы: 60

Бренд: zapco Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды