Austin Kontore Crestview Chicken Coop Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 54

background image

© 2009 Austin Kontore LLC

Page 39 of 54

From the outside of the coop, measure 1 ½” from the
outer left edge of the Door Slide Rail. Make a mark in the
center of the Rail.

Measure 1 ½” from the outer right edge of the Door Slide
Rail. Make a mark in the center of the Rail.

Drill a pilot hole in the right edge, at the mark just made.

Note:

This pilot hole can be deep, as the parts will be

fastened with a 3” long screw.

Fasten the outside right corner of the Door Slide Rail to
the Core Square and into the Post using a 3” screw.

Drill a pilot hole in the left edge, at the mark previously
made.

Fasten the outside left corner of the Door Slide Rail to the
Core Square and into the Post using a 3” screw.

Rotate coop to the opposite side and

REPEAT

the

above process for the

remaining Door Slide Rail

.

Goal:

Two lower door slide rails installed on opposite

sides of the coop.

«
...
37
38
39
40
41
...
»

Содержание Crestview Chicken Coop























































Отзывы:

Нет отзывов

Похожие инструкции для Crestview Chicken Coop

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: NEC Страницы: 29

Бренд: 3M Страницы: 48

Бренд: 3M Страницы: 19

Speedglas G5-01

Бренд: 3M Страницы: 62

Quickfit Nexus Exit

Бренд: Thomas & Betts Страницы: 2

Бренд: CAE Healthcare Страницы: 108

Бренд: Cannon Страницы: 36

Бренд: Cannon Страницы: 40

Бренд: NARGESA Страницы: 34

Бренд: Echo Страницы: 6

Pro Attachment Series

Бренд: Echo Страницы: 28

Бренд: Echo Страницы: 2

Pro Vantage 12+ Series

Бренд: Ecco Страницы: 6

Бренд: Garelick Страницы: 2

Бренд: Gardico Страницы: 2

Бренд: OceanSat Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды