Austin Kontore Crestview Chicken Coop Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 54

background image

© 2009 Austin Kontore LLC

Page 40 of 54

Door Slide Rails:
Middle Level

(2) Door Slide Rails
(prefabricated)

(2) 19” Door Screen Units
(fabricated earlier)

(6) 1 5/8” Screws
(Three per Door Slide Rail)

(4) 3” Screws
(Two per Door Slide Rail)

Door Slide Rail installation continues. In this section, the two middle level Rails are installed onto the
middle Core Square. The process is almost identical to the previous section, so please reference “Door
Slide Rails: Lower Level” for the details of marking, drilling, and fastening.

Important:

To make the photographs in this section clearer, the fixed screens and panels were

removed. When building your coop, two of the sides will have the fixed screens and panels installed.

Rotate the coop so that an open side is facing you. (A side
where you have just installed the lower Door Slide Rail.)

Take one of the 19” Screen Door units and place it inside
the “slot” of the Lower Door Slide Rail.

Place one of the Door Slide Rails on top of the Screen
Door.

«
...
38
39
40
41
42
...
»

Содержание Crestview Chicken Coop























































Отзывы:

Нет отзывов

Похожие инструкции для Crestview Chicken Coop

Бренд: ACS Страницы: 56

Бренд: GE Страницы: 43

Бренд: GE Страницы: 37

Бренд: GE Страницы: 210

Бренд: GE Страницы: 160

Бренд: GE Страницы: 146

Бренд: GE Страницы: 6

Бренд: GE Страницы: 27

Бренд: GE Страницы: 4

BTL PA0400 Series

Бренд: Balluff Страницы: 22

Micropulse BTL5 Series

Бренд: Balluff Страницы: 12

BNI IOW-560-W01-K022

Бренд: Balluff Страницы: 32

Бренд: Baltic Страницы: 68

Бренд: Baltic Страницы: 68

Max Charge MC-612

Бренд: Balmar Страницы: 12

BTL PA0400 Series

Бренд: Balluff Страницы: 204

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды