ARM ARM1176JZF-S Скачать руководство пользователя страница 333 | Manualshive

Страница: 333 / 759

background image

Memory Management Unit

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

6-16

ID012310

Non-Confidential, Unrestricted Access

Table 6-3 shows how the MMU and cache interpret the cache policy bits.

You can choose the write allocation policy that an implementation supports. The Allocate On
Write and No Allocate On Write cache policies indicate the preferred allocation policy for a
memory region, but you must not rely on the memory system implementing that policy. The
processor does not support Inner Allocate on Write.

Not all Inner and Outer cache policies are mandatory. Table 6-4 lists possible implementation
options.

When the MMU is off and TexRemap=0:

•

All data accesses are treated as Shared, Inner Strongly Ordered, Outer Non-cacheable.

•

Instruction accesses are treated as Non-Shared, Inner and Outer Write-Through, No
Allocate on Write, when the Instruction Cache is on, I=1, bit [12], see

c1, Control Register

on page 3-44.

Instruction accesses are treated as Shared, Inner Strongly Ordered, Outer Non-Cacheable,
when the Instruction Cache is off, see

Behavior with MMU disabled

on page 6-9.

TexRemap=1 configuration

Only three bits, TEX[0], C, and B, are relevant in this configuration. The OS can use the
TEX[2:1] bits to manage the page tables.

In this configuration the processor provides the OS with a remap capability for the memory
attribute. Two CP15 registers, the

Primary Region Remap Register

(PRRR) and the

Normal

Memory Region Register

(NMRR) come into effect.

Table 6-3 Cache policy bits

BB or AA bits

Cache policy

b00

Noncacheable

b01

Write-Back cached, Write Allocate

b10

Write-Through cached, No Allocate on Write

b11

Write-Back cached, No Allocate on Write

Table 6-4 Inner and Outer cache policy implementation options

Cache policy

Implementation options

Supported by
the processor

Inner Noncacheable

Mandatory.

Yes

Inner Write-Through

Mandatory.

Yes

Inner Write-Back

Optional. If not supported, the memory system must implement this as
Inner Write-Through.

Yes

Outer Noncacheable

Mandatory.

System-dependent

Outer Write-Through

Optional. If not supported, the memory system must implement this as
Outer Non-cacheable.

System-dependent

Outer Write-Back

Optional. If not supported, the memory system must implement this as
Outer Write-Through.

System-dependent

«
...
331
332
333
334
335
...
»

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Бренд: Omega Engineering Страницы: 34

IPAM-1600s Series

Бренд: C-Com Страницы: 148

Бренд: Kaptia Страницы: 14

Бренд: Rane Страницы: 128

Бренд: Acard Страницы: 34

Бренд: Shure Страницы: 113

HiGain Line Unit HLU-388

Бренд: PairGain Страницы: 7

Бренд: XtendLan Страницы: 17

Бренд: H3C Страницы: 62

Бренд: Williams Sound Страницы: 2

TeleLite 720920 Series

Бренд: Positron Страницы: 21

Бренд: Hama Страницы: 10

Бренд: TQ Страницы: 2

Бренд: Honeywell Страницы: 8

Бренд: Honeywell Страницы: 2

HN350401 Series

Бренд: Honeywell Страницы: 3

Бренд: Honeywell Страницы: 4

Rae SensorRAE 4R+

Бренд: Honeywell Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды