background image

INSTALLATION INSTRUCTIONS

Put Bar Code Here

39−00002

Q7055C Honeywell Meter Point 

Connect

GENERAL

WARNING

This equipment generates, uses and can radiate

radio frequency energy, and if not installed and

used in accordance with the Instructions Manual,

may cause interference with radio communication.

It has been tested and found to comply with the

limits for a Class A computing device pursuant to

Subpart J of Part 15 or FCC Rules, which are

designed to provide reasonable protection against

such interference when operated in a commercial

environment. Operation of this equipment in a

residential area is likely to cause interference, in

which case, users at their own expense will be

required to take whatever measures may be

required to correct the interference. Any

unauthorized modification of this equipment may

result in the revocation of the owner's authority to

continue its operation.

GENERAL

The Q7055C series Honeywell Meter Point Connect (MPC)

provides connection to sub-metering devices via M-Bus level

converter using MeterBus Protocol. The Meter Point

communicates to EBI-Central over an industry standard 10/

100BaseT Ethernet LAN. It delivers exceptional price/

performance to meet the requirements of both building owners

and service providers. The Meter Point communicates to sub-

metering devices via a M-Bus level converter using M-Bus

standards: EN13757-3 and EN1434-3. With its combination of

scalable performance, density, and low per-port pricing, the

MPC allows network layer capabilities to be extended to a

much wider range of network configurations and

environments. Customers can now gain the advantages of

high-performance network and services, including traffic

management, to more locations throughout the network. The

Q7055C MPC-Model M1 provides a single RS-485 DC

coupled M-Bus-compatible communication channel for

submetering devices.

M-Bus compatible sub-metering devices support baud-rates

from 300 bps to 19200 bps. The Q7055C MPC-Model M2

provides two RS-485 DC coupled M-Bus-compatible

communication channels for submetering devices.

Fig. 1. MPC network.

The MPC uses the LAN connection to provide a seamless

communication to the requesting device. Status information,

like LAN communication activity, field bus traffic

communication and system heartbeat of the MPC is indicated

by LEDs on the device front.

HONEYWELL METER POINT CONNECT TOPOLOGY

M25412

EBI SERVER

MPC M-BUS CH1

M-BUS LEVEL

CONVERTER

M-BUS ROUTER

MPC M-BUS CH1, CH2

M-BUS SUPPORTED

SUB-METERING DEVICES

M-BUS SUPPORTED

SUB-METERING DEVICES

ETHERNET

EBI CLIENT

LC

LOCAL AREA NETWORK

M-BUS LEVEL

CONVERTER

LC1

LC2

RS485-RS232 

CONVERTER

RS232

RS485

RS232

RS485-RS232 

CONVERTER

RS485

RS232

RS232

RS485

Содержание Q7055C1053









Отзывы: