background image

Q7055C HONEYWELL METER POINT CONNECT

5

39-00002

Consult form no. 39-00003, Q7055C Honeywell Meter Point

Connect MPC-Model M1/Model M2 Checkout & Test for

additional information on field bus wiring.

CABLES AND CONNECTORS

DB9F Null Modem Connector

Fig. 5 illustrates a serial connector for the field bus. Fig. 6

shows how to configure a Null Modem Cable DB9F.

Fig. 6. Serial connector (female connector is numbered as 

shown).

Fig. 7. Signal connections for DB9F Null Modem Cable.

Ethernet Connection

See Fig. 7 for MPC Ethernet connection.

Fig. 8. MPC Ethernet connector.

RJ-45 LAN Connector

The MPC provides a standard RJ-45 connector for 10/

100BaseT Ethernet LAN connection. This section describes

the pin layout for the RJ-45 connector. Most Ethernet local

area networks use twisted pair wiring. 10/100BaseT networks

are physically laid out in a star topology, where each piece of

equipment on the network is connected to a central switch.

The wiring is connected to devices using a plug that

resembles a phone jack called RJ-45. See Table 2 on page 5

for details.

Connect MPC to Switch

To connect a MPC device to a LAN via an Ethernet Switch, the

required cable should be configured as shown in Fig. 8.

Fig. 9. Straight-through pinning for MPC to Ethernet 

Switch connections.

9 = RI

5 = GROUND

8 = CTS

7 = RTS

6 = DSR

M19592

2 = RxD

3 = TxD

4 = DTR

1 = DCD

DCD

DSR

GND

RTS 

CTS

DTR 

RxD 

2

3

4

1

6

5

7

8

2

3

6

1

4

5

7

8

TxD

RI 

DCD

DTR

GND

RTS 

CTS

DSR 

RxD 

TxD

RI 

M19594

9

9

M22399

8-PIN MODULAR 
CONNECTOR RJ-45

Rx -  

Rx + 

Tx + 

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

Tx - 

Rx -  

M19596

Rx + 

Tx + 

Tx - 

Содержание Q7055C1053









Отзывы: