background image

Q7055C HONEYWELL METER POINT CONNECT

7

39-00002

Fig. 12. Parts and controls on rear side of MPC.

8—CH2

2-pin connector for field bus channel 2 connection, electrically

isolated, meets EMC and FCC requirements.

Field Bus wiring is described in the Field Bus Connection

(Ch1/Ch2) section.

NOTE: The Ch2 field bus connector is only available on

two-channel devices. It is not available on the

MPC-Model M1.

9—CH1/CH2 BUS TERMINATION SWITCHES

These switches are used to select field bus termination and

biasing. For a detailed description of the bus termination

switch positions, refer to the Bus Termination Switch section of

form no.39-00003, Q7055C Honeywell Meter Point Connect

MPC-Model M1/Model M2 Configuration, Checkout & Test

Guide.

NOTE: The Bus Termination Switch option near the Ch2

field bus connector is only available on MPC-

Model M2 two-channel devices. It is not available

on the MPC-Model M1.

10—CH1

2-pin connector for field bus channel 1 connection, electrically

isolated, meets EMC and FCC requirements. Field Bus wiring

is described in the Field Bus Connection (Ch1/Ch2) section.

11—AC/DC IN 24V

Power connector for 24 VAC (50 Hz to 60 Hz) or 24 VDC

 power supplies and chassis ground

. An external power

supply is required. See the Power Connection section of this

document for details.

12—RS-232

9-pin SUB-D male RS-232 connector, electrically isolated, PC

pin compatible, protected against spikes. This interface is

used for initial device setup and requires a standard Null-

Modem cable when interfacing to a PC.

13—10/100BASET

10/100BaseT RJ-45 Ethernet LAN-connector, meets the

requirements of ANSI/TIA/EIA 586 Category 5, for unshielded

twisted pair connections.

MAINTENANCE PROCEDURES

The Q7055C MPC has no user replaceable fuses. For service,

contact your local Honeywell Automation & Control Solutions

office as listed in the phone book, or contact a regional office

as shown at the end of this document.

MPC - Model M1

8

10

9

11

13

12

A(+) B(-)

Ch1

AC/DC IN

24V

10/100

normal

~

~

+

-

+

10

9

11

13

12

A(+) B(-)

Ch1

A(+) B(-)

Ch2

AC/DC IN

24V

10/100

normal

normal

~

~

+

-

+

MPC- Model M2

M30015

Содержание Q7055C1053









Отзывы: