Q7055C HONEYWELL METER POINT CONNECT
3
39-00002
BEFORE INSTALLATION
Perform the following steps prior to installing the MPC device:
1.
Verify that the product has been received without dam-
age.
2.
Verify that the correct MPC device has been delivered.
3.
Check the package contents. The following items are
included in each product package:
— Honeywell Meter Point Connect device.
— 50017367-001 or Model 3A-181WP24, P/N
EMS240075-P5P-SZ Power Supply or SMI18-24-V-P5
Power Supply.
— Honeywell Meter Point Connect Installation Instruc-
tions.
— Bag of installation materials as follows: one 3-pole
Phoenix power connector, and one or two Phoenix
controller bus channel connectors.
4.
Read the Connections section carefully prior to connect-
ing power, ground and data interface cables to the MPC.
5.
Refer to the installation instructions for each component
connected to the MPC.
Applicable Literature
— Form no. 39-00001, Q7055C1053 MPC-M1 (Single M-
Bus) and Q7055C1055 MPC-M2 (Dual M-Bus) Speci-
fication Data Sheet.
— Form no. 39-00002, Q7055C1053 MPC-M1 (Single M-
Bus) and Q7055C1055 MPC-M2 (Dual M-Bus) Instal-
lation Literature.
— Form no. 39-00003, Q7055C1053 MPC-M1 (Single M-
Bus) and Q7055C1055 MPC-M2 (Dual M-Bus) Config-
uration, Checkout & Test Guide.
— Form no. 39-00004, Q7055C1053 MPC-M1 (Single M-
Bus) and Q7055C1055 MPC-M2 (Dual M-Bus) MPC
Router Installation Guide.
— Form no. 39-00005, Q7055C1053 MPC-M1 (Single M-
Bus) and Q7055C1055 MPC-M2 (Dual M-Bus) Soft-
ware Release Bulletin.
WIRING
CAUTION
Shock Hazard. Removal of the MPC cover can
result in electrical shock
Do not remove cover. There are no user serviceable
parts inside.
Location and Mounting
The MPC device is intended for installation only indoors in a
dry location. It can be mounted in several ways; as a single
device, up to three stacked devices, or wall/cabinet mounted.
Single Device
The following illustration shows the single MPC device
operating position; for example, on a desk (see Fig 2).
Fig. 3. Single Device Operating Position.
Stacked Devices
MPC devices may also be stacked. Because of stability
issues, it is recommended not to stack more than three
devices (see Fig 3).
NOTE: There are cooling slots on the top and bottom of
the MPC housing.
Fig. 4. Stacked Devices.
Reset Power
LAN
10
ACT
Mode
M-Bus
Ch2
Rx Tx
M-Bus
Ch1
Rx Tx
100
Boot NML
M22586
METER POINT CONNECT MODEL M2
-Bus
Reset Power
LAN
10
ACT
Mode
Rx Tx
M-Bus
Ch1
M-Bus
Ch2
Rx Tx
100
Boot NML
Reset Power
LAN
10
ACT
Mode
Rx Tx
Rx Tx
100
Boot NML
Reset Power
LAN
10
ACT
Mode
Rx Tx
Rx Tx
100
Boot NML
M25115
M-Bus
Ch1
M-Bus
Ch2
M-Bus
Ch1
M-Bus
Ch2
HONEYWELL
METER POINT CONNECT MODEL M2
-Bus
HONEYWELL
METER POINT CONNECT MODEL M2
-Bus
HONEYWELL
METER POINT CONNECT MODEL M2
-Bus
