ARM ARM1176JZF-S Скачать руководство пользователя страница 378 | Manualshive

Страница: 378 / 759

background image

Level One Memory System

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

7-7

ID012310

Non-Confidential, Unrestricted Access

7.3

Tightly-coupled memory

The TCM is designed to provide low-latency memory that can be used by the processor without
the unpredictability that is a feature of caches.

You can use such memory to hold critical routines, such as interrupt handling routines or
real-time tasks where the indeterminacy of a cache is highly undesirable. In addition you can
use it to hold scratch pad data, data types whose locality properties are not well suited to
caching, and critical data structures such as interrupt stacks.

You can separately configure the size of the

Instruction TCM

(ITCM) and the size of the

Data

TCM

(DTCM) to be 0KB, 4KB. 8KB, 16KB, 32KB or 64KB. For each side, ITCM and DTCM:

•

If you configure the TCM size to be 4KB you get one TCM, of 4KB, on this side.

•

If you configure the TCM size to be larger than 4KB you get two TCMs on this side, each
of half the configured size. So, for example, if you configure an ITCM size of 16KB you
get two ITCMs, each of size 8KB.

Table 7-1 lists all possible TCM configurations:

When the number of TCM on one side is 2, to make the implementation easier, the TCM for this
side are implemented as one single RAM. This RAM then has a size in the 0-64 KB range. The
lower part of the RAM corresponds to the TCM called TCM0 and the upper part corresponds to
TCM1.

You can also configure each individual TCM to contain Secure or Non-secure data. You make
this configuration in CP15 register c9, accessible in Secure state only. See

c9, Data TCM

Non-secure Control Access Register

on page 3-93 and

c9, Instruction TCM Non-secure Control

Access Register

on page 3-94 for more information. After reset, all TCMs are configured as

Secure.

The TCM Status Register in CP15 c0 describes what TCM options and TCM sizes can be
implemented, see

c0, TCM Status Register

on page 3-24.

Each Data TCM is implemented in parallel with the Data Cache and each Instruction TCM is
implemented in parallel with the Instruction Cache. Each TCM has a single movable base
address, specified in CP15 register c9, see

c9, Data TCM Region Register

on page 3-89 and

c9,

Instruction TCM Region Register

on page 3-91.

The size of each TCM can differ from the size of a cache way, but forms a single contiguous
area of memory. Figure 7-1 on page 7-4 shows the entire level one memory system. To access
each of the TCM region and TCM Access Control registers, the TCM Selection registers are set
to the TCM of interest, see

c9, TCM Selection Register

on page 3-96.

Table 7-1 TCM configurations

Configured TCM size

Number of TCMs

Size of each TCM

0KB

0

0

4KB

1

4KB

8KB

2

4KB

16KB

2

8KB

32KB

2

16KB

64KB

2

32KB

«
...
376
377
378
379
380
...
»

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Express EtherNetwork DFE-670TXD

Бренд: D-Link Страницы: 4

Бренд: DAD Страницы: 36

Бренд: D-Link Страницы: 2

Бренд: 3xLogic Страницы: 2

Бренд: Cabletron Systems Страницы: 21

H3C S7500E Series

Бренд: H3C Страницы: 34

SR8800 IM-FW-II

Бренд: H3C Страницы: 5

H3C S7500E Series

Бренд: H3C Страницы: 50

Бренд: Harman Kardon Страницы: 66

SAFETank Series

Бренд: Raidon Страницы: 49

Бренд: 3Com Страницы: 16

Бренд: QNAP Страницы: 54

Бренд: QuickLink Страницы: 8

2000 IDU Series

Бренд: EMS Страницы: 52

Бренд: AXIOMTEK Страницы: 2

Бренд: Renesas Страницы: 4

Бренд: LevelOne Страницы: 142

Бренд: ICP DAS USA Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды