manualshive.com logo in svg

ARM ARM1176JZF-S, Техническое справочное руководство

Продукт "ARM ARM1176JZF-S" - это высокотехнологичный процессор, предназначенный для использования во многих устройствах. Вы можете бесплатно скачать техническое руководство для этого продукта на нашем сайте. Руководство содержит всю необходимую информацию для работы с процессором. Скачайте его сейчас!

Поделиться
Скачать
background image

System Control Coprocessor 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-147

ID012310

Non-Confidential, Unrestricted Access

You can use the System Validation Cache Size Mask Register, in a validation simulation 
environment, to perform validation with cache and TCM sizes that appear to be a different size 
from those that are actually implemented. The validation environment for the processor contains 
validation RAMs that support cache and TCM size masking using this register. When you write 
to the System Validation Cache Size Mask Register, the processor behaves as though the caches 
and TCMs are the sizes that are written to the register. The sizes written to the register are 
reflected in:

•

The sizes of the cache and TCM RAMs.

•

The sizes of the caches in the Cache Type Register, see 

c0, Cache Type Register

 on 

page 3-21, the number of Instruction and Data TCM banks in the TCM Status Register, 
see 

c0, TCM Status Register

 on page 3-24, the sizes of the TCMs in the Instruction TCM 

Region Register, see 

c9, Instruction TCM Region Register

 on page 3-91, and the Data 

TCM Region Register, see 

c9, Data TCM Region Register

 on page 3-89.

•

The number and use of cache master valid bits, see 

Cache Master Valid Registers

 on 

page 3-8.

•

The hazard detection logic that prevents the same line being allocated twice into the 
caches.

•

The DMA. If the TCMs are both masked as not present, then the DMA also appears not 
to be present.

Note

 You must not modify the System Validation Cache Size Mask Register in a manufactured 
device. Physical RAMs do not support cache and TCM size masking. Therefore, any attempt to 
mask cache and TCM sizes using this register causes address aliasing effects and problems with 
cache master valid bits, that result in incorrect operation and Unpredictable effects.

3.2.58

c15, Instruction Cache Master Valid Register

The purpose of the Instruction Cache Master Valid Register is to save and restore the instruction 
cache master valid bits on entry to and exit from dormant mode, see 

Dormant mode

 on 

page 10-4. You might also use this register during debug.

The Instruction Cache Master Valid Register is:

•

in CP15 c15

•

a 32-bit read/write register in Secure world only

•

accessible in privileged modes only.

The number of Master Valid bits in the register is a function of the cache size. There is one 
Master Valid bit for each 8 cache lines:

For instance, there are 64 Master Valid bits for a 16KB cache. You can access Master Valid bits 
through 32-bit registers indexed using Opcode_2. The maximum number of 32-bit registers 
required for the largest cache size, 64KB, is 8. The Master Valid bits fill the registers from the 
LSB of the lowest numbered register upwards.

Writes to unimplemented Valid bits have no effect, and reads return 0. The reset value is 0.

Attempts to write to this register in Secure Privileged mode when 

CP15SDISABLE

 is HIGH 

result in an Undefined exception, see 

TrustZone write access disable

 on page 2-9.

Master Valid bits =  

cache size

line length in bytes x 8

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Paradyne 8540 Installation Instructions Manual preview
8540
Бренд: Paradyne Страницы: 12
ZALMAN CNPS6500B-AlCu User Manual preview
CNPS6500B-AlCu
Бренд: ZALMAN Страницы: 4
Renesas Converter Board R0E5212BACFG00 User Manual preview
Converter Board R0E5212BACFG00
Бренд: Renesas Страницы: 6
H3C NIC-FC730i-Mb-2-32G Manual preview
NIC-FC730i-Mb-2-32G
Бренд: H3C Страницы: 37
Keithley DAS-1800HR Series User Manual preview
DAS-1800HR Series
Бренд: Keithley Страницы: 139
Bridgeworks Tamar FCSAS102800 User Manual preview
Tamar FCSAS102800
Бренд: Bridgeworks Страницы: 56
Ciara Horizon D10750 Disassembly Manual preview
Horizon D10750
Бренд: Ciara Страницы: 14
IBA ibaBM-FOX-i-3o-D Manual preview
ibaBM-FOX-i-3o-D
Бренд: IBA Страницы: 13
Idex KNIGHT MT-300 Instruction Manual preview
KNIGHT MT-300
Бренд: Idex Страницы: 4
Extron electronics Network Device PIP 444 User Manual preview
Network Device PIP 444
Бренд: Extron electronics Страницы: 62
Fujitsu FUTRO S700 Datasheet preview
FUTRO S700
Бренд: Fujitsu Страницы: 7
Fujitsu LQFP-100P Operation Manual preview
LQFP-100P
Бренд: Fujitsu Страницы: 16
Fujitsu GP5-FC102 User Manual preview
GP5-FC102
Бренд: Fujitsu Страницы: 32
Fujitsu FPT-20P-M06 Specification Sheet preview
FPT-20P-M06
Бренд: Fujitsu Страницы: 6
Fujitsu FMC-16FX FAMILY ADA-16FX-ETHERNET User Manual preview
FMC-16FX FAMILY ADA-16FX-ETHERNET
Бренд: Fujitsu Страницы: 14
Fujitsu LAVENDER Documentation preview
LAVENDER
Бренд: Fujitsu Страницы: 15
Fujitsu FUTRO S550-2 Operating Manual preview
FUTRO S550-2
Бренд: Fujitsu Страницы: 42
Fujitsu FUTRO S700 Operating Manual preview
FUTRO S700
Бренд: Fujitsu Страницы: 107

Бренды по названию

Популярные бренды

Загрузить еще бренды