ARM ARM1176JZF-S Скачать руководство пользователя страница 137 | Manualshive

Страница: 137 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-5

ID012310

Non-Confidential, Unrestricted Access

3.1.2

System control and configuration

The purpose of the system control and configuration registers is to provide overall management
of:

•

TrustZone behavior

•

memory functionality

•

interrupt behavior

•

exception handling

•

program flow prediction

•

coprocessor access rights for CP0-CP13.

The system control and configuration registers also provide the processor ID.

The system control and configuration registers consist of three 32-bit read only registers and
eight 32-bit read/write registers. Figure 3-1 shows the arrangement of registers in this functional
group.

Figure 3-1 System control and configuration registers

To use the system control and configuration registers you read or write individual registers that
make up the group, see

Use of the system control coprocessor

on page 3-12.

System validation

Secure User and Non-secure Access
Validation Control

c15, Secure User and Non-secure Access Validation Control
Register

on page 3-132

System Validation Counter

c15, System Validation Counter Register

on page 3-140

System Validation Operations

c15, System Validation Operations Register

on page 3-142

System Validation Cache Size Mask

c15, System Validation Cache Size Mask Register

on

page 3-145

a. Returns device ID code.

Table 3-1 System control coprocessor register functions (continued)

Function

Register/operation

Reference to description

CRn

c1

Coprocessor Access Control Register

Auxiliary Control Register

Control Register

1

2

0

c0

0

Opcode_2

CRm

Opcode_1

c0

ID Code Register

0

c0

0

Write-only

Accessible in User mode

Read-only

Read/write

2

Secure Configuration Register

Non-secure Access Control Register

CPUID Registers

CPUID Registers

CPUID Registers

CPUID Registers

CPUID Registers

CPUID Registers

CPUID Registers

Secure Debug Enable Register

1

c12

Monitor Vector Base Address Register

Non-secure or Secure Vector Base Address Register

1

0

c0

0

Interrupt Status Register

2

c1

{0-7}

c1

{0-7}

{0-7}

{0-7}

{0-7}

{0-7}

{0-7}

c2

c3

c4

c5

c6

c7

0

c1

«
...
135
136
137
138
139
...
»

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Бренд: GE Страницы: 4

Бренд: Aastra Страницы: 2

Бренд: Abus Страницы: 60

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

PCard-E 021L-D5 Series

Бренд: ORiNG Страницы: 2

Бренд: EZCast Pro Страницы: 4

Бренд: ekwb Страницы: 2

Homecraft Rolyan AA6240

Бренд: Patterson Страницы: 2

Бренд: Tripp Lite Страницы: 2

Бренд: TP-Link Страницы: 2

OG-HDTV-SDI-UHD

Бренд: Opengear Страницы: 7

Бренд: Linksys Страницы: 17

Бренд: MSI Страницы: 5

Бренд: Pico Macom Страницы: 8

PRIMERGY TX150 S2

Бренд: Fujitsu Страницы: 163

Бренд: Fujitsu Страницы: 20

Бренд: Huawei Страницы: 2

Бренд: Huawei Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды