ARM ARM1176JZF-S Скачать руководство пользователя страница 731 | Manualshive

Страница: 731 / 759

background image

Summary of ARM1136JF-S and ARM1176JZF-S Processor Differences

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

B-5

ID012310

Non-Confidential, Unrestricted Access

Intelligent Energy Management

The ARM1136JF-S processor provides partial support for Dormant mode. The ARM1176JZF-S
processor extends this functionality and provides optional support for IEM and Dormant mode.

For Dormant mode the ARM1176JZF-S processor provides the option to instantiate a
placeholder that contains all the necessary input clamps to RAM blocks.

The ARM1176JZF-S RTL hierarchy is separated into three blocks to support three different
power domains:

•

all the RAMs

•

the core logic, clocked by

CLKIN

and

FREECLKIN

•

four optional IEM Register Slices.

The register slices can provide an asynchronous interface between:

•

the Level 2 ports, powered by V

Core

and clocked by

CLKIN

•

the AXI system, powered by V

Soc

and clocked by

ACLK

signals, one clock for each port.

Level shifters and clamps must be instantiated between power domains.ARM1176JZF-S
processors do not implement the asynchronous interface present in the ARM1136JF-S
processor and, if implemented, you can use the IEM Register Slices to provide the asynchronous
interface in the Level 2 ports of the ARM1136JF-S processor.

VFP

The power domains in the ARM1176JZF-S processor are divided for:

•

the VFP

•

all other logic outside the VFP

•

a placeholder for clamping logic between these two blocks.

With this hierarchy you can switch off the VFP power, to save power, when the VFP is not in use.

B.2.4

SmartCache

Unlike ARM1136JF-S processors, the ARM1176JZF-S processor does not implement the
SmartCache feature for the Tightly-Coupled Memories. As a consequence, the TCMs in
ARM1176JZF-S processors always behave as local RAMs and the SC bit, bit [1], of each TCM
Region Register is Read As Zero and Ignored on writes. The SmartCache dedicated valid and
dirty RAMs are not implemented in the ARM1176JZF-S processor.

The ARM1176JZF-S processor does not include these RAMs:

•

ITCValidRAM

•

DTCValidRAM

•

DTCDirtyRAM.

B.2.5

CPU ID

The ARM1176JZF-S processor implements the revised ARMv7 CPU ID scheme using CP15
c0.

B.2.6

Block transfer operations

Unlike ARM1136JF-S processors, the ARM1176JZF-S processor does not implement some
block transfer operations and these operations are Undefined in ARM1176JZF-S processors:

•

Prefetch Range operations, Instruction and Data

«
...
729
730
731
732
733
...
»

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Бренд: FabiaTech Страницы: 4

DR-4100P Series

Бренд: Idis Страницы: 30

Бренд: BSS Audio Страницы: 20

Бренд: Reeven Страницы: 2

CLICK PLUS C2-02CPU

Бренд: Automationdirect.com Страницы: 10

Бренд: Ruckus Wireless Страницы: 102

Бренд: Renesas Страницы: 941

InvenSense RoboKit1

Бренд: TDK Страницы: 13

Бренд: Tandy Страницы: 24

Бренд: ACTi Страницы: 12

Converter Board R0E521237CFK00

Бренд: Renesas Страницы: 6

Бренд: EZCast Pro Страницы: 4

Бренд: ekwb Страницы: 2

Бренд: Taiwan Commate Computer Inc. Страницы: 25

Бренд: Greenlee Страницы: 52

Бренд: Intellinet Страницы: 2

Бренд: Moxa Technologies Страницы: 8

ClareVision CV-M161620-04

Бренд: Clare Controls Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды