ARM ARM1176JZF-S Скачать руководство пользователя страница 251 | Manualshive

Страница: 251 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-119

ID012310

Non-Confidential, Unrestricted Access

Access in the Non-secure world depends on the DMA bit, see

c1, Non-Secure Access Control

Register

on page 3-55. These registers can be accessed in User mode if the U bit, see

c11, DMA

User Accessibility Register

on page 3-107, for the currently selected channel is set to 1.

Table 3-118 lists the results of attempted access for each mode.

To access the DMA Channel Status Register set DMA Channel Number Register to the
appropriate DMA channel and read CP15 with:

•

Opcode_1 set to 0

•

CRn set to c11

•

CRm set to c8

•

Opcode_2 set to 0.

MRC p15, 0, <Rd>, c11, c8, 0

; Read DMA Channel Status Register

In the event of an error, the appropriate Start Address Register contains the address that faulted,
unless the error is an external error that is set to b11010 by bits [11:7].

A channel with the state of Queued changes to Running automatically if the other channel, if
implemented, changes to Idle, or Complete or Error, with no error.

When a channel completes all of the transfers of the DMA, so that all changes to memory
locations caused by those transfers are visible to other observers, its status is changed from
Running to Complete or Error. This change does not happen before the external accesses from
the transfer complete.

If the processor attempts to access memory locations that are not marked as shared, then the ES
bits signal an Unshared error for either:

•

a DMA transfer in User mode

•

a DMA transfer that has the UM bit set in the DMA Control Register.

A DMA transfer where the external address is within the range of the TCM also results in an
Unshared data error.

If the DMA channel is configured Secure, in the event of an error the processor asserts the

nDMASIRQ

pin provided it is not masked. If the channel is configured Non-secure, in the event

of an error the processor asserts the

nDMAIRQ

pin, provided it is not masked. In the event of

an external abort on a page table walk caused by the DMA, the processor asserts the

nDMAEXTERRIRQ

output.

Table 3-118 Results of access to the DMA Channel Status Register

U
bit

DMA
bit

Secure
Privileged

Non-secure
Privileged

Secure User

Non-secure User

Read

Write

Read

Write

Read

Write

Read

Write

0

0

Data

Undefined
exception

Undefined
exception

Undefined
exception

Undefined
exception

Undefined
exception

Undefined
exception

Undefined
exception

1

Data

Undefined
exception

Data

Undefined
exception

Undefined
exception

Undefined
exception

Undefined
exception

Undefined
exception

1

0

Data

Undefined
exception

Undefined
exception

Undefined
exception

Data

Undefined
exception

Undefined
exception

Undefined
exception

1

Data

Undefined
exception

Data

Undefined
exception

Data

Undefined
exception

Data

Undefined
exception

«
...
249
250
251
252
253
...
»

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Бренд: FabiaTech Страницы: 4

Бренд: GAMDIAS Страницы: 15

Бренд: Paradyne Страницы: 1

Бренд: Accusys Страницы: 34

Бренд: Xtreme Страницы: 83

Бренд: Vacron Страницы: 16

LatticeMico GPIO

Бренд: Lattice Semiconductor Страницы: 28

Total Access 1500 Dual FXS/DPO

Бренд: ADTRAN Страницы: 2

MTDOT-868 Series

Бренд: Multitech Страницы: 60

Бренд: SIIG Страницы: 8

Q-SYS QIO-GP8x8

Бренд: QSC Страницы: 13

Бренд: Moxa Technologies Страницы: 8

Бренд: Patton electronics Страницы: 8

Бренд: Omnia Страницы: 130

System 200V PC 288

Бренд: VIPA Страницы: 54

8 Channel Dimmer Module CLX-1DIM8

Бренд: Crestron Страницы: 1

2000i 6.5-7.1 Service Pack 1

Бренд: Rimage Страницы: 174

Бренд: ProCurve Страницы: 406

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды