ARM ARM1176JZF-S Скачать руководство пользователя страница 190 | Manualshive

Страница: 190 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-58

ID012310

Non-Confidential, Unrestricted Access

Table 3-53 lists how the bit values correspond with the Translation Table Base Register 0
functions.

Attempts to write to this register in Secure Privileged mode when

CP15SDISABLE

is HIGH

result in an Undefined exception, see

TrustZone write access disable

on page 2-9.

Table 3-54 lists the results of attempted access for each mode.

A write to the Translation Table Base Register 0 updates the address of the first level translation
table from the value in bits [31:7] of the written value, to account for the maximum value of 7
for N. The number of bits of this address that the processor uses, and therefore, the required
alignment of the first level translation table, depends on the value of N, see

c2, Translation Table

Base Control Register

on page 3-60.

A read from the Translation Table Base Register 0 returns the complete address of the first level
translation table in bits [31:7] of the read value, regardless of the value of N.

To use the Translation Table Base Register 0 read or write CP15 c2 with:

•

Opcode_1 set to 0

•

CRn set to c2

•

CRm set to c0

Table 3-53 Translation Table Base Register 0 bit functions

Bits

Field name

Function

[31:14-N]

a

Translation table base 0

Holds the translation table base address, the physical address of the first level
translation table. The reset value is 0.

[13-N:5]

a

-

UNP/SBZ.

[4:3]

RGN

Indicates the Outer cacheable attributes for page table walking:

b00 = Outer Noncacheable, reset value

b01 = Write-back, Write Allocate

b10 = Write-through, No Allocate on Write

b11 = Write-back, No Allocate on Write.

[2]

P

If the processor supports ECC, it indicates to the memory controller it is enabled
or disabled. For ARM1176JZF-S processors this is 0:

0 =

Error-Correcting Code

(ECC) is disabled, reset value

1 = ECC is enabled.

[1]

S

Indicates the page table walk is to Non-Shared or to Shared memory:

0 = Non-Shared, reset value

1 = Shared.

[0]

C

Indicates the page table walk is Inner Cacheable or Inner Noncacheable:

0 = Inner noncacheable, reset value

1 = Inner cacheable.

a. For an explanation of N see

c2, Translation Table Base Control Register

on page 3-60.

Table 3-54 Results of access to the Translation Table Base Register 0

Secure Privileged

Non-secure Privileged

User

Read

Write

Read

Write

Secure data

Secure data

Non-secure data

Non-secure data

Undefined exception

«
...
188
189
190
191
192
...
»

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 30

Express EtherNetwork DFE-670TXD

Бренд: D-Link Страницы: 4

Бренд: DAD Страницы: 36

Бренд: D-Link Страницы: 2

Network Video Recorders

Бренд: e-Line Technology Страницы: 34

SCSI PC Card REX-9530V

Бренд: Ratoc Systems Страницы: 30

Бренд: Delta Страницы: 2

Бренд: IDT Страницы: 207

Elite Controller

Бренд: RANA Systems Страницы: 328

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

Бренд: Rainbow Страницы: 2

Бренд: Intercoax Страницы: 2

Bolide BN-NVR/NX

Бренд: GSA Страницы: 101

-K6-2/450 - MHz Processor

Бренд: AMD Страницы: 98

Бренд: C&H Technologies Страницы: 2

Бренд: Z3 Technology Страницы: 83

ClareVision CV-M161620-04

Бренд: Clare Controls Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды