ARM ARM1176JZF-S Скачать руководство пользователя страница 277 | Manualshive

Страница: 277 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-145

ID012310

Non-Confidential, Unrestricted Access

3.2.57

c15, System Validation Cache Size Mask Register

The purpose of the System Validation Cache Size Mask Register is to change the apparent size
of the caches and TCMs as they appear to the processor, for validation by simulation. It does not
change the physical size of the caches and TCMs in a manufactured device.

The System Validation Cache Size Mask Register is:

•

in CP15 c15

•

a 32 bit read/write register common to the Secure and Non-secure worlds

•

accessible in User and Privileged modes.

Figure 3-75 shows the arrangement of bits for the System Validation Cache Size Mask Register.

Figure 3-75 System Validation Cache Size Mask Register format

Table 3-146 lists how the bit values correspond with the System Validation Cache Size Mask
Register functions.

SBZ

31

15 14

12 11 10

8 7 6

4 3 2

0

DTCM

S
B
Z

ITCM

S
B
Z

DCache

S
B
Z

ICache

Write enable

Table 3-146 System Validation Cache Size Mask Register bit functions

Bits

Field name

Function

[31]

Write enable

Enables the update of the Cache and TCM sizes:

0 = The Cache and TCM sizes are not changed, reset value.

1 = The Cache and TCM sizes take the new values that the DTCM, ITCM, DCache and ICache
fields of this register specify.

Note

This is bit is write access only and Read As Zero.

[30:15]

SBZ

UNP/SBZ.

[14:12]

DTCM

Specifies apparent size of Data TCM and apparent number of Data TCM banks, as it appears
to the processor. All other values are reserved:

b000 = Not present

b011 = 1 bank, 4KB

b100 = 2 banks, 4KB each

b101 = 2 banks, 8KB each

b110 = 2 banks, 16KB each

b111 = 2 banks, 32KB each.

[11]

SBZ

UNP/SBZ.

[10:8]

ITCM

Specifies apparent size of Instruction TCM and apparent number of Instruction TCM banks, as
it appears to the processor. All other values are reserved:

b000 = Not present

b011 = 1 bank, 4KB

b100 = 2 banks, 4KB each

b101 = 2 banks, 8KB each

b110 = 2 banks, 16KB each

b111 = 2 banks, 32KB each.

«
...
275
276
277
278
279
...
»

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Бренд: Observint Страницы: 117

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

Бренд: Belkin Страницы: 72

Бренд: 3Com Страницы: 18

Бренд: Supermicro Страницы: 24

Бренд: Commell Страницы: 9

Бренд: Kramer Страницы: 2

Wireless Connectivity Cape

Бренд: Element14 Страницы: 2

Бренд: Rainbow Страницы: 2

Бренд: Intercoax Страницы: 2

Бренд: Digital Voice Systems Страницы: 32

Бренд: ATTO Technology Страницы: 2

Бренд: S&P Страницы: 3

Бренд: ProSoft Страницы: 53

Бренд: LST Страницы: 1

Бренд: Lanner Страницы: 141

Бренд: Uctronics Страницы: 12

Бренд: Z3 Technology Страницы: 83

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды