ARM ARM1176JZF-S Скачать руководство пользователя страница 272 | Manualshive

Страница: 272 / 759

background image

System Control Coprocessor

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

3-140

ID012310

Non-Confidential, Unrestricted Access

Access to the Count Register 1 in User mode depends on the V bit, see

c15, Secure User and

Non-secure Access Validation Control Register

on page 3-132. The Count Register 1 is always

accessible in Privileged modes. Table 3-141 lists the results of attempted access for each mode.

To access Count Register 1 read or write CP15 with:

•

Opcode_1 set to 0

•

CRn set to c15

•

CRm set to c12

•

Opcode_2 set to 3.

For example:

MRC p15, 0, <Rd>, c15, c12, 3

; Read Count Register 1

MCR p15, 0, <Rd>, c15, c12, 3

; Write Count Register 1

The value in Count Register 1 is 0 at Reset.

You can use the Performance Monitor Control Register to set Count Register 1 to zero.

3.2.55

c15, System Validation Counter Register

The purpose of the System Validation Counter Register is to count core clock cycles to trigger
a system validation event.

The System Validation Counter Register is:

•

in CP15 c15

•

a 32 bit read/write register common to the Secure and Non-secure worlds

•

accessible in User and Privileged modes.

The System Validation Counter Register consists of one 32-bit register that performs four
functions. Table 3-142 lists the arrangement of the functions in this group. The reset value is 0.

The reset, interrupt, and fast interrupt counters are 32-bits wide. The external debug request
counter is 6 bits wide. Figure 3-74 on page 3-141 shows the arrangement of bits for the external
debug request counter.

Table 3-141 Results of access to the Count Register 1

V bit

Secure Privileged

Non-secure Privileged

User

Read

Write

Read

Write

Read

Write

0

Data

Data

Data

Data

Undefined exception

Undefined exception

1

Data

Data

Data

Data

Data

Data

Table 3-142 System validation counter register operations

CRn

Opcode_1

CRm

Opcode_2

R/W

Operation

c15

0

c12

1

R/W

Reset counter

2

R/W

Interrupt counter

3

R/W

Fast interrupt counter

7

W

External debug request counter

«
...
270
271
272
273
274
...
»

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Бренд: Patton electronics Страницы: 16

Бренд: Qualys Страницы: 2

Storagelibrary T24

Бренд: Tandberg Data Страницы: 28

Бренд: ZALMAN Страницы: 4

Бренд: VCS Страницы: 118

TD-3316B4-16P-A1

Бренд: TVT Digital Страницы: 2

PowerBeam PBE-5AC-400-ISO

Бренд: Ubiquiti Страницы: 23

RADEON 9800 PRO

Бренд: ATI Technologies Страницы: 20

Бренд: Promise Technology Страницы: 26

Бренд: Dataprobe Страницы: 16

Бренд: ETAS Страницы: 84

Extreme Spirit Il

Бренд: Thermaltake Страницы: 2

Бренд: Matrix Switch Corporation Страницы: 48

ENHANCED PSD 239 H2R

Бренд: ADTRAN Страницы: 2

Hotwire 5620 RTU

Бренд: Paradyne Страницы: 20

Бренд: Abocom Страницы: 70

Бренд: ADTRAN Страницы: 4

mvHYPERION-32R16

Бренд: Matrix Vision Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды