ARM ARM1176JZF-S Скачать руководство пользователя страница 660

Страница: 660 / 759

VFP Programmer’s Model

ARM DDI 0301H

20-19

ID012310

Non-Confidential, Unrestricted Access

20.4.5

Media and VFP Feature Register 0

The purpose of the Media and VFP Feature Register 0 is to provide information about the
features that the VFP unit contains.

Media and VFP Feature Register 0 is:

•

a 32-bit read-only register

•

accessible in any mode when the VFP is enabled by the EN bit, see

Floating-point

exception register, FPEXC

on page 20-16

•

accessible only in Privileged modes when the VFP is disabled by the EN bit.

Figure 20-8 shows the bit arrangement for Media and VFP Feature Register 0.

Figure 20-8 Media and VFP Feature Register 0 format

Table 20-9 shows how the bit values correspond with the Media and VFP Feature Register 0
functions.

The values in the Media and VFP Feature Register 0 are implementation defined.

16 15

8 7

Table 20-9 Media and VFP Feature Register 0 bit functions

Bits

Name

Function

[31:28]

Indicates the VFP hardware support level when user traps are disabled.

0x1

, In ARM1176JZF-S processors when Flush-to-Zero and Default_NaN and Round-to-Nearest are

all selected in FPSCR, the coprocessor does not require support code. Otherwise floating point
support code is required.

[27:24]

Indicates support for short vectors.

0x1

, ARM1176JZF-S processors support short vectors.

[23:20]

Indicates support for hardware square root.

0x1

, ARM1176JZF-S processors support hardware square root.

[19:16]

Indicates support for hardware divide.

0x1

, ARM1176JZF-S processors support hardware divide.

[15:12]

Indicates support for user traps.

0x1

, ARM1176JZF-S processors support software traps, support code is required.

[11:8]

Indicates support for double precision VFP.

0x1

, ARM1176JZF-S processors support v2.

[7:4]

Indicates support for single precision VFP.

0x1

, ARM1176JZF-S processors support v2.

[3:0]

Indicates support for the media register bank.

0x1

, ARM1176JZF-S processors support 16, 64-bit registers.

Содержание ARM1176JZF-S























































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ARM1176JZF-S

Отзывы:

Похожие инструкции для ARM1176JZF-S

Бренды по названию

Популярные бренды

ARM ARM1176JZF-S, Техническое справочное руководство

Результаты поиска

Содержание ARM1176JZF-S

Отзывы:

Похожие инструкции для ARM1176JZF-S

Бренды по названию

Популярные бренды