ARM ARM1176JZF-S Скачать руководство пользователя страница 186

Страница: 186 / 759

System Control Coprocessor

ARM DDI 0301H

3-54

ID012310

Non-Confidential, Unrestricted Access

To use the Secure Configuration Register read or write CP15 with:

•

Opcode_1 set to 0

•

CRn set to c1

•

CRm set to c1

•

Opcode_2 set to 0.

For example:

MRC p15, 0, <Rd>, c1, c1, 0

; Read Secure Configuration Register data

MCR p15, 0, <Rd>, c1, c1, 0

; Write Secure Configuration Register data

An attempt to access the Secure Configuration Register from any state other than Secure
privileged results in an Undefined exception.

3.2.11

c1, Secure Debug Enable Register

The purpose of the Secure Debug Enable Register is to provide control of permissions for debug
in Secure User mode, see Chapter 13

Debug

Table 3-49 lists the purposes of the individual bits in the Secure Debug Enable Register.

The Secure Debug Enable Register is:

•

in CP15 c1

•

a 32 bit register in the Secure world only

•

accessible in Secure privileged modes only.

Figure 3-30 shows the arrangement of bits in the register.

Figure 3-30 Secure Debug Enable Register format

Table 3-49 lists how the bit values correspond with the Secure Debug Enable Register functions.

SBZ

1 0

SUNIDEN

SUIDEN

Table 3-49 Secure Debug Enable Register bit functions

Bits

Field name

Function

[31:2]

This field is UNP when read. Write as the existing value.

[1]

SUNIDEN

Enables Secure User non-invasive debug:

0 = Non-invasive debug is not permitted in Secure User mode, reset value

1 = Non-invasive debug is permitted in Secure User mode.

[0]

SUIDEN

Enables Secure User invasive debug:

0 = Invasive debug is not permitted in Secure User mode, reset value

1 = Invasive debug is permitted in Secure User mode.

Содержание ARM1176JZF-S























































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ARM1176JZF-S

Отзывы:

Похожие инструкции для ARM1176JZF-S

Бренды по названию

Популярные бренды

ARM ARM1176JZF-S, Техническое справочное руководство

Результаты поиска

Содержание ARM1176JZF-S

Отзывы:

Похожие инструкции для ARM1176JZF-S

Бренды по названию

Популярные бренды