ARM ARM1176JZF-S Скачать руководство пользователя страница 652 | Manualshive

Страница: 652 / 759

background image

VFP Programmer’s Model

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

20-11

ID012310

Non-Confidential, Unrestricted Access

20.3.4

FMRRS

FMRRS transfers data in two consecutively numbered single-precision VFP11 registers to two
ARM11 registers. The ARM11 registers do not have to be contiguous. Figure 20-4 shows the
format of the FMRRS instruction.

Figure 20-4 FMRRS instruction format

Syntax

FMRRS {<cond>} <Rd>, <Rn>, <registers>

where:

<cond>

Is the condition under which the instruction is executed. If <cond> is omitted, the
AL, always, condition is used.

<Rd>

Specifies the destination ARM11 register for the Sm VFP11 coprocessor
single-precision value.

<Rn>

Specifies the destination ARM11 register for the S(m + 1) VFP11 coprocessor
single-precision value.

<registers>

Specifies the pair of consecutively numbered single-precision VFP11 source
registers, separated by a comma and surrounded by brackets. If m is the number
of the first register in the list, the list is encoded in the instruction by setting Sm
to the top four bits of m and M to the bottom bit of m. For example, if

<registers>

is {S16, S17}, the Sm field of the instruction is b1000 and the M bit is 0.

Architecture version

All

Exceptions

None

Operation

If ConditionPassed(cond) then

Rd = Sm
Rn = S(m + 1)

Notes

Conversions

In the programmer’s model, FMRRS does not perform any conversion of
the value transferred. Arithmetic instructions using Rd and Rn treat the
contents as an integer, whereas most VFP11 instructions treat the Sm and
S(m + 1) values as single-precision floating-point numbers.

Invalid register lists

If Sm is b1111 and M is 1, an encoding of S31, the instruction is
Unpredictable.

Use of R15

If R15 is specified for Rd or Rn, the results are Unpredictable.

1 1 0 0 0 1 0 1

Rn

Rd

1 0 1 0 0 0 M 1

Sm

31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0

cond

«
...
650
651
652
653
654
...
»

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Бренд: Octavo Страницы: 28

Бренд: Obihai Страницы: 2

Бренд: Quantum Страницы: 20

Бренд: IOtech Страницы: 16

OMB-DAQBOARD-3000 Series

Бренд: Omega Страницы: 108

Бренд: Altera Страницы: 93

NetVanta 6355 PoE

Бренд: ADTRAN Страницы: 46

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

InterReach Fusion SingleStar

Бренд: LGC wireless Страницы: 154

PARTNER PC CARD

Бренд: Avaya Страницы: 4

Бренд: National Instruments Страницы: 130

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

CY62136EV30 MoBL

Бренд: Cypress Semiconductor Страницы: 12

Бренд: Rainbow Страницы: 2

Бренд: Intercoax Страницы: 2

Бренд: ICOP Technology Страницы: 34

Бренд: Meinberg Страницы: 14

ULTRIX-FM-NS-1RU

Бренд: Ross Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды