ARM ARM1176JZF-S Скачать руководство пользователя страница 179

Страница: 179 / 759

System Control Coprocessor

ARM DDI 0301H

3-47

ID012310

Non-Confidential, Unrestricted Access

Attempts to read or write the Control Register from Secure or Non-secure User modes results
in an Undefined exception.

Attempts to write to this register in Secure Privileged mode when

CP15SDISABLE

is HIGH

result in an Undefined exception, see

TrustZone write access disable

on page 2-9.

Attempts to write Secure modify only bit in Non-secure privileged modes are ignored.

Attempts to read Secure modify only bits return the Secure bit value. Table 3-40 lists the actions
that result from attempted access for each mode.

Use of the Control Register

To use the Control Register it is recommended that you use a read modify write technique. To
use the Control Register read or write CP15 with:

•

Opcode_1 set to 0

•

CRn set to c1

•

CRm set to c0

•

Opcode_2 set to 0.

For example:

MRC p15, 0, <Rd>, c1, c0, 0

; Read Control Register configuration data

MCR p15, 0, <Rd>, c1, c0, 0

; Write Control Register configuration data

Normally, to set the V bit and the B, EE, and U bits you configure signals at reset.

The V bit depends on

VINITHI

at reset:

•

VINITHI

LOW sets V to 0

•

VINITHI

HIGH sets V to 1.

[2]

C bit

Banked

Enables level one data cache.

0 = Data cache disabled, reset value.

1 = Data cache enabled.

[1]

A bit

Banked

Enables strict alignment of data to detect alignment faults in data accesses. The A bit
setting takes priority over the U bit.

0 = Strict alignment fault checking disabled, reset value.

1 = Strict alignment fault checking enabled.

[0]

M bit

Banked

Enables the MMU.

0 = MMU disabled, reset value.

1 = MMU enabled.

Table 3-39 Control Register bit functions (continued)

Bits

Field
name

Access

Function

Table 3-40 Results of access to the Control Register

Access type

Secure Privileged

Non-secure Privileged

User

Read

Write

Secure modify only

Secure bit

Ignored

Undefined exception

Banked

Secure bit

Non-secure bit

Undefined exception

Содержание ARM1176JZF-S























































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание ARM1176JZF-S

Отзывы:

Похожие инструкции для ARM1176JZF-S

Бренды по названию

Популярные бренды

ARM ARM1176JZF-S, Техническое справочное руководство

Результаты поиска

Содержание ARM1176JZF-S

Отзывы:

Похожие инструкции для ARM1176JZF-S

Бренды по названию

Популярные бренды