ARM ARM1176JZF-S Скачать руководство пользователя страница 478 | Manualshive

Страница: 478 / 759

background image

Debug

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

13-4

ID012310

Non-Confidential, Unrestricted Access

When debugging in Monitor debug-mode, you can program new debug events through CP14.
This coprocessor is the software interface of all the debug resources such as the breakpoint and
watchpoint registers. See

CP14 c1, Debug Status and Control Register (DSCR)

on page 13-7 to

learn how to set the processor debug unit into Monitor debug-mode.

Note

Monitor debug-mode, used for debugging, is not the same as Secure Monitor mode.

13.2.3

Secure Monitor mode and debug

Debug can be restricted to one of three levels, Non-secure only, Non-secure and Secure User
only, or any Secure or Non-secure levels so that you can prevent access to Secure parts of the
system while still permitting Non-secure and optionally Secure User parts to be debugged. This
is controlled by the

SPIDEN

and

SPNIDEN

signals and the two bits SUIDEN and SUNIDEN

in the Secure Debug Enable Register in the system control coprocessor, see

External debug

interface

on page 13-28 and

c1, Secure Debug Enable Register

on page 3-54.

Invasive debug

Invasive debug is debug where the system can be both observed and controlled
like all of the debug in this section that enables you to halt the processor and
examine and modify registers and memory.

SPIDEN

and SUIDEN control invasive debug permissions.

Non-invasive debug

Non-invasive is debug where the system can only be observed but not affected.
The ETM interface, the System Performance Monitor and the DBGTAP program
counter sample register provide non-invasive debug.

SPNIDEN

and SUNIDEN control non-invasive debug permissions.

13.2.4

Virtual addresses and debug

Unless otherwise stated, all addresses in this chapter are

Modified Virtual Addresses

(MVA) as

the

ARM Architecture Reference Manual describes.

For example, the

Breakpoint Value

Registers

(BVR) and

Watchpoint Value Registers

(WVR) must be programmed with MVAs.

The terms

Instruction Modified Virtual Address

(IMVA) and

Data Modified Virtual Address

(DMVA), where used, mean the MVA corresponding to an instruction address and the MVA
corresponding to a data address respectively.

13.2.5

Programming the debug unit

The processor debug unit is programmed using

CoProcessor 14

(CP14). CP14 provides:

•

instruction address comparators for triggering breakpoints

•

data address comparators for triggering watchpoints

•

a bidirectional

Debug Communication Channel

(DCC)

•

all other state information associated with processor debug.

CP14 is accessed using coprocessor instructions in Monitor debug-mode, and certain debug
scan chains in Debug state, see Chapter 14

Debug Test Access Port

to learn how to access the

processor debug unit using scan chains.

«
...
476
477
478
479
480
...
»

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Бренд: Ubiquiti Страницы: 24

Бренд: Garland Страницы: 4

Бренд: National Instruments Страницы: 9

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

Бренд: Waves Страницы: 41

RabbitCore RCM4400W

Бренд: Rabbit Страницы: 126

PARTNER PC CARD

Бренд: Avaya Страницы: 4

Бренд: u-blox Страницы: 29

Бренд: Dantel Страницы: 62

OP-8000-EDFA-1U Series

Бренд: Optostar Страницы: 9

Бренд: IEI Technology Страницы: 3

Бренд: Eneo Страницы: 68

Through Hole Power Inductors 1411

Бренд: Delta Electronics Страницы: 1

DataPlot CB1224

Бренд: B-G Instruments Страницы: 4

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

Бренд: QTech Страницы: 406

Бренд: Renesas Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды