ARM ARM1176JZF-S Скачать руководство пользователя страница 732 | Manualshive

Страница: 732 / 759

background image

Summary of ARM1136JF-S and ARM1176JZF-S Processor Differences

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

B-6

ID012310

Non-Confidential, Unrestricted Access

•

Stop Prefetch Range operations

•

Read Block Transfer Status Register operations.

The ARM1176JZF-S processor implements all the other block transfer operations:

•

Invalidate Cache Range, Instruction and Data

•

Clean Data Cache Range

•

Clean and Invalidate Data Cache Range.

B.2.7

Tightly-Coupled Memories

The ARM1136JF-S processor implements zero or one Tightly Coupled Memories on each side,
Instruction and Data. The possible TCM sizes for ARM1136JF-S for each side are:

•

0KB

•

4KB

•

8KB

•

16KB

•

32KB

•

64KB.

The ARM1176JZF-S processor implements zero, one or two Tightly Coupled Memories on
each side. For each side, the two TCMs are physically located within one RAM. Table B-1 lists
the possible configurations for ARM1176JZF-S Tightly-Coupled Memories for each side:

B.2.8

Fault Address Register

ARM1136JF-S processors includes an Instruction Fault Address Register in the system control
coprocessor, CP15, with the encoding:

•

Opcode_1 = 0

•

Crn = 6

•

Crm = 0

•

Opcode_2 = 1.

The ARM1136JF-S IFAR is only updated on watchpoints.

The ARM1136JF-S IFAR is the Watchpoint Fault Address Register in ARM1176JZF-S
processors. The WFAR is in the CP14 coprocessor with the encoding:

•

Opcode_1 = 0

•

Crn = 0

•

Crm = 6

•

Opcode_2 = 0.

Table B-1 TCM for ARM1176JZF-S processors

Number of TCM

TCM size

RAM size

0

0 KB

0 KB

1

4 KB

4 KB

2

4 KB

8 KB

2

8 KB

16 KB

2

16 KB

32 KB

2

32 KB

64 KB

«
...
730
731
732
733
734
...
»

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

Бренд: C4i Страницы: 8

Бренд: Datasat Страницы: 32

Бренд: Paradox Страницы: 4

Бренд: Kontron Страницы: 42

Бренд: Cytron Technologies Страницы: 13

Extreme Gaming VGA Cooler GV1000

Бренд: ZALMAN Страницы: 7

PCIe/PXIe-6301 Series

Бренд: JYTEK Страницы: 46

Бренд: C&T Solution Страницы: 129

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

LIQMAX III ELC-LMT120-ARGB

Бренд: ENERMAX Страницы: 32

PCard-E 021L-D5 Series

Бренд: ORiNG Страницы: 2

Бренд: Dahua Страницы: 113

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Бренд: Intel Страницы: 112

Бренд: Ubiquiti Страницы: 13

VIGI NVR1004H-4P

Бренд: TP-Link Страницы: 2

Бренд: PairGain Страницы: 80

Бренд: ADS Technologies Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды