manualshive.com logo in svg

ARM ARM1176JZF-S, Техническое справочное руководство

Продукт "ARM ARM1176JZF-S" - это высокотехнологичный процессор, предназначенный для использования во многих устройствах. Вы можете бесплатно скачать техническое руководство для этого продукта на нашем сайте. Руководство содержит всю необходимую информацию для работы с процессором. Скачайте его сейчас!

Поделиться
Скачать
background image

Debug Test Access Port 

ARM DDI 0301H

Copyright © 2004-2009 ARM Limited. All rights reserved.

14-11

ID012310

Non-Confidential, Unrestricted Access

Note

 There are some exceptions to this use of INTEST and EXTEST to control reading and writing 
the scan chain. These are noted in the relevant scan chain descriptions.

Scan chain 0, debug ID register (DIDR)

Purpose 

Debug.

Length 

8 + 32 = 40 bits.

Description 

Debug identification. This scan chain accesses CP14 debug register 0, the debug 
ID register. Additionally, the eight most significant bits of this scan chain contain 
an implementor code. This field is hardwired to 

0x41

, the implementor code for 

ARM Limited, as specified in the 

ARM Architecture Reference Manual

. This 

register is read-only. Therefore, EXTEST has the same effect as INTEST.

Order 

Figure 14-7 shows the order of bits in scan chain 0.

Figure 14-7 Scan chain 0 bit order

Scan chain 1, Debug Status and Control Register (DSCR)

Purpose 

Debug.

Length 

32 bits.

Description 

This scan chain accesses CP14 register 1, the DSCR. This is mostly a read/write 
register, although certain bits are read-only for the Debug Test Access Port. See 

CP14 c1, Debug Status and Control Register (DSCR)

 on page 13-7 for details of 

DSCR bit definitions, and for read/write attributes for each bit. Those bits defined 
as cleared on read are only cleared if INTEST is selected.

Order 

Figure 14-8 shows the order of bits in scan chain 1.

Figure 14-8 Scan chain 1 bit order

DBGTDI

DBGTDO

Data[39:0]

Implementor

39

32 31

0

DIDR[31:0]

DBGTDI

DBGTDO

Data[31:0]

DSCR[31:0]

31

0

DSCR[31:0]

Содержание ARM1176JZF-S
























































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ARM1176JZF-S

D-Link DFE-690TXD Quick Install Manual preview
DFE-690TXD
Бренд: D-Link Страницы: 12
dbx ProVocal Specifications preview
ProVocal
Бренд: dbx Страницы: 2
H3C H3C S7500E Series Instruction Manual preview
H3C S7500E Series
Бренд: H3C Страницы: 34
H3C SR8800 IM-FW-II Manual preview
SR8800 IM-FW-II
Бренд: H3C Страницы: 5
H3C H3C S7500E Series Installation Manual preview
H3C S7500E Series
Бренд: H3C Страницы: 50
LevelOne FPC-0103T Manual preview
FPC-0103T
Бренд: LevelOne Страницы: 31
ESD ECS-CPCIs/FPGA Hardware Manual preview
ECS-CPCIs/FPGA
Бренд: ESD Страницы: 28
IEI Technology PUZZLE-IN003B User Manual preview
PUZZLE-IN003B
Бренд: IEI Technology Страницы: 86
Dahua Technology Lite N42B1P Series Quick Start Manual preview
Lite N42B1P Series
Бренд: Dahua Technology Страницы: 14
Delta Electronics Through Hole Power Inductors 1411 Product Specifications preview
Through Hole Power Inductors 1411
Бренд: Delta Electronics Страницы: 1
XJTAG XJLink2-CFM User Manual preview
XJLink2-CFM
Бренд: XJTAG Страницы: 9
Xilinx Zynq-7000 Manual preview
Zynq-7000
Бренд: Xilinx Страницы: 8
Comelit IPNVR004BPOE Manual preview
IPNVR004BPOE
Бренд: Comelit Страницы: 19
ENERMAX LIQMAX III ELC-LMT120-ARGB User Manual preview
LIQMAX III ELC-LMT120-ARGB
Бренд: ENERMAX Страницы: 32
netsys NVF-2400S User Manual preview
NVF-2400S
Бренд: netsys Страницы: 164
Spirent A2-400 Installation Instructions Manual preview
A2-400
Бренд: Spirent Страницы: 22
UMAX Technologies SuperMac E100 User Manual preview
SuperMac E100
Бренд: UMAX Technologies Страницы: 27
Cooler Master MCY-C3P1-KWNN Manual preview
MCY-C3P1-KWNN
Бренд: Cooler Master Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды