Arctic Cat S2008ACAAAUSG Скачать руководство пользователя

Страница: 81 / 104

MAINTENANCE



NOTE: When adjusting air pres-

sure, all weight must be removed
from the front suspension, and
the shock absorbers must be fully
extended.



NOTE: Adding air pressure will

increase the air spring force;
reducing air pressure will
decrease air spring force.

1. Remove the air valve cap from

the shock.

2. Thread the valve of Air Shock

Pump (p/n 2603-614) onto the

shock air valve approximately six

rotations.



NOTE: As the pump is being

attached to the shock, the hose
will fill with air. This will result in a
lower gauge pressure 0.14-3.52
kg/cm

(2-5 psi).

3. To decrease air pressure in the

shock, press the black bleed valve

button half way down and hold

until desired pressure is attained.



NOTE: Pressing the button fully

down and releasing it will allow
only a small amount of air to
escape (micro-adjust).

4. To increase air pressure in the

shock, pump until desired pres-

sure is attained.

5. Remove the pump valve from the

shock air valve.



NOTE: As the pump valve is

being removed from the shock,
the sound of air loss is from the
pump hose, not from the shock.

6. Install the air valve cap onto the

shock.

Skid Frame Front Arm



NOTE: On some models, the

front arm limiter straps are not
adjustable.

The skid frame front arm shock spring

and limiter straps are adjustable. How-

ever, Arctic Cat recommends that the

shock spring be maintained as loose as

possible. Tightening the skid frame

front arm shock spring may cause

improper balance and may ruin the

handling features of the snowmobile.

The length adjustment of the front arm

limiter straps determines the weight

distribution between the front of the

skid frame and the skis. Tightening the

limiter strap (shortening the strap) will

pull up on the front of the skid frame

and will increase ski pressure. Loosen-

ing the limiter strap (lengthening the

strap) lowers the front of the skid

frame and decreases ski pressure.

When customizing the amount of ski

pressure, be sure to adjust both straps

equally and do not over-adjust the lim-

iter straps to adversely affect steering

and operator control of the snowmo-

bile. Some experimentation may be

required until the proper adjustment

for the operator’s individual style is

obtained.

! WARNING

Do not exceed 105 kg/cm

(150

psi) in the shock.

! WARNING

Do not adjust the front arm limiter
straps to a point at which steering
and operator control of the snow-
mobile are adversely affected.

Содержание S2008ACAAAUSG









































































































Результаты поиска

Содержание S2008ACAAAUSG

Отзывы:

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

Популярные бренды

Arctic Cat S2008ACAAAUSG, Руководство оператора

Результаты поиска

Содержание S2008ACAAAUSG

Отзывы:

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

Популярные бренды