Arctic Cat S2008ACAAAUSG Скачать руководство пользователя | Manualshive

Страница: 93 / 104

background image

PREPARATION FOR STORAGE

89

PREPARATION FOR STORAGE

Prior to storing the snowmobile, it

must be properly serviced to prevent

corrosion and component deteriora-

tion. An authorized Arctic Cat Snow-

mobile dealer should perform this

service; however, the owner/ operator

can perform this service if desired.

This service is at the discretion and

expense of the snowmobile owner. To

prepare the snowmobile for storage,

Arctic Cat recommends the following

procedure:

1. Clean the seat cushion with a

damp cloth and Arctic Cat Vinyl

Protectant (p/n 0638-313).

2. Clean the snowmobile thoroughly

by hosing dirt, oil, grass, and

other foreign matter from the skid

frame, tunnel, hood, and belly

pan. Allow the snowmobile to dry

thoroughly. DO NOT get water

into any part of the engine.



NOTE: On 4-stroke models,

change the engine oil and clean
the air filter; then proceed to step
9.

3. Place the rear of the snowmobile

up on a shielded safety stand.

4. On the 500/600/800/1000 cc

engine models, start the engine

and allow to idle. With the engine

idling, pry the intake boot for-

ward; then spray Arctic Cat

Engine Storage Preserver (p/n

0436-888) into the intakes until

the engine exhaust starts to smoke

heavily or until the engine starts

to drop in RPM. Turn engine off.



NOTE: On the 500/600/800/1000

cc engine models after step 4,
proceed to step 9.



NOTE: On some standard mod-

els, the air-intake silencer is a
one-piece unit, and the silencer
boot(s) can be removed to access
the intake bore(s). Remove the
boots; then proceed to step 8.



NOTE: On some standard mod-

els, the air-intake silencer
includes a cover/tool tray assem-
bly and a baffle/resonator, and the
silencer boot cannot be removed
to access the intake bores. Pro-
ceed to step 5.

5. Open the air-intake silencer

cover; then remove the Phillips-

head screws securing the cover/

tool tray assembly to the silencer.

6. Close the cover; then tip the

cover/tool tray assembly forward

and out of its slots and remove the

assembly.

7. Using a large flat-blade screw-

driver, remove the baffle/resona-

tor tabs from the air-intake

silencer slots and remove the baf-

fle/resonator to access the intake

bores.



NOTE: The baffle/resonator can

be removed more easily by remov-
ing the back tabs first.

8. Start the engine and allow to idle.

With the engine idling, spray Arc-

tic Cat Engine Storage Preserver

(p/n 0436-888) into the intake(s)

until the engine exhaust starts to

smoke heavily or until the engine

starts to drop in RPM. Turn

engine off.



NOTE: On some models, install

the air-intake silencer boot(s); on
some models, install the baffle/
resonator and the cover/tool tray
assembly.

«
...
91
92
93
94
95
...
»

Содержание S2008ACAAAUSG









































































































Отзывы:

Нет отзывов

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды