Arctic Cat S2008ACAAAUSG Скачать руководство пользователя

Страница: 87 / 104

MAINTENANCE

741-329A

Installing Headlight

Bulb (F-Series/Jaguar

Z1/T-Series/TZ1

Models)

1. Plug the wiring harness into the

headlight bulb.

2. Insert the bulb into the headlight

housing.

3. Lift the front of the console

enough to allow the headlight

housing to be installed; then

install the housing making sure

the forks of the housing go into

the grommets on top of the air-

intake silencer. Secure with the

cap screw and lock nut.

741-505A

4. Position the console onto the air-

intake silencer; then secure with

the single torx-head cap screw

beneath the console (located

between the headlights).

5. Install the two torx-head cap

screws located to the outside of

the headlight adjustment knobs;

then tighten securely.

6. Check headlight aim (see Adjust-

ing Headlight Aim in this sub-

section).

Adjusting Headlight

Aim

The headlight can be adjusted for ver-

tical aim of the HIGH/LOW beam.

The geometric center of HIGH beam

zone is to be used for vertical aiming.

1. Position the snowmobile on a

level floor so the headlight is

approximately 8 m (25 ft) from an

aiming surface (wall or similar

surface).



NOTE: There should be an

“average” operating load on the
snowmobile when adjusting head-
light aim.

2. Measure the distance from the

floor to midpoint of the headlight.

3. Using the measurement obtained

in step 2, make a horizontal mark

on the aiming surface.

4. Make a vertical mark which inter-

sects the horizontal mark on the

aiming surface directly in front of

the headlight.

! CAUTION

Do not touch the glass portion of
the bulb. If the glass portion is
touched, it must be cleaned with a
dry cloth before installing.

! WARNING

Do not operate the snowmobile
unless headlight beam is adjusted
properly. An incorrectly adjusted
beam will not provide the operator
the optimum amount of light.

Содержание S2008ACAAAUSG









































































































Результаты поиска

Содержание S2008ACAAAUSG

Отзывы:

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

Популярные бренды

Arctic Cat S2008ACAAAUSG, Руководство оператора

Результаты поиска

Содержание S2008ACAAAUSG

Отзывы:

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

Популярные бренды