manualshive.com logo in svg

Arctic Cat S2008ACAAAUSG, Руководство оператора

Поделиться
Скачать
Arctic Cat S2008ACAAAUSG Скачать руководство пользователя страница 73

MAINTENANCE

69

0739-269

2. Remove the pin/hairpin clip

securing the brake pads to the cal-

iper assembly.

3. Remove the brake fluid reservoir

cover; then remove most of the

brake fluid from the reservoir.

Replace the cover.

NOTE: The above procedure will

allow room for the fluid from the
caliper when the pistons are
pushed into the caliper for install-
ing new brake pads. Replacing the
cover will prevent fluid spillage.

4. Using a pair of pliers, pull one

brake pad out of the caliper

assembly.

NOTE: Changing one pad at a

time will prevent one piston from
pushing out the other piston from
the caliper.

5. Using a flat-blade tool, slowly

and carefully push the piston into

the caliper.

6. Position the new brake pads into

the caliper.

7. Repeat steps 4-6 for the other pad;

then secure the pads with the pin/

hairpin clip.

8. Remove the reservoir cover and

remove the remaining fluid; then

fill the reservoir with fresh fluid.

9. Pump the brake lever to ensure

correct positioning of the brake

pads; then release.

10. Fill the reservoir to the proper

level with fresh brake fluid.

NOTE: When new brake pads

are installed, a “burnishing” pro-
cess is required. Drive the snow-
mobile slowly and compress the
brake lever several times until the
pads just start to warm up; then
allow them to cool down. This pro-
cedure stabilizes the pad material
and extends the life of the pads.

DRIVE BELT

The drive belt transfers power from

the drive clutch to the driven pulley. If

the belt is worn, cracked, or stretched,

maximum power will not be transmit-

ted and the belt could also fail and

therefore must be replaced. Periodic

checks (at least once a month under

normal usage) of two drive belt speci-

fications are essential.

1. Measure the outside circumfer-

ence of the drive belt. The belt

should be within the recom-

mended range in circumference.

2. Measure the outside width of the

drive belt. The belt should be

within the recommended range in

width.

3. Check the belt for cracking, fray-

ing, etc.

If any of the specifications or condi-

tions are unsatisfactory, replace the

drive belt.

NOTE: Drive belts should be

purchased from an authorized
Arctic Cat Snowmobile dealer, as
Arctic Cat drive belts are made to
exact specifications and of quality
material. Belts made by other
manufacturers may not be of the
same specifications or quality
and, therefore, usage could result
in poor performance and prema-
ture belt failure.

Содержание S2008ACAAAUSG









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды