manualshive.com logo in svg

Arctic Cat S2008ACAAAUSG, Руководство оператора

Поделиться
Скачать
Arctic Cat S2008ACAAAUSG Скачать руководство пользователя страница 64

60

MAINTENANCE

NOTE: If the center electrode

insulators are light gray, white, or
black and if the carburetor adjust-
ments (on carbureted models), oil-
injection pump synchronization,
and ignition timing are correct,
different heat-range spark plugs
may be necessary. Authorized
Arctic Cat Snowmobile dealers
have detailed spark plug informa-
tion. Consult a dealer before
changing spark plugs, as incor-
rect heat-range spark plugs could
cause poor engine performance
or engine damage.

CHECKING/

ADJUSTING VALVE 

CLEARANCE (660 cc/

1100 cc Models)

After 3500 miles (660 cc)/5000 miles

(1100 cc) or prior to seasonal storage,

valve clearance should be checked and

adjusted as necessary.

NOTE: Take the snowmobile to

an authorized Arctic Cat Snowmo-
bile dealer for inspection and ser-
vice. If not under warranty, this
service is at the discretion and
expense of the snowmobile owner.

BATTERY (Electric 

Start Models)

These standard and sealed batteries

after being in service require regular

cleaning and recharging in order to

deliver peak performance and maxi-

mum service life. The following pro-

cedures are recommended for cleaning

and maintaining standard and sealed

batteries. Always read and follow

instructions provided with battery

chargers and battery products.

NOTE: Battery maintenance

may be done by the snowmobile
owner if qualified to do so. If the
owner does not feel qualified, take
the snowmobile to an authorized
Arctic Cat Snowmobile dealer for
this service. This service is at the
discretion and expense of the
snowmobile owner.

To remove and charge the battery, use
the following procedure:

! CAUTION

If a spark plug is light gray, white,
or black and another is tan or light
brown, take the snowmobile to an
authorized Arctic Cat Snowmobile
dealer for inspection and service.
If not under warranty, this service
is at the discretion and expense
of the snowmobile owner.

! CAUTION

It is critical that the checking/
adjusting valve clearance be done
at the recommended intervals or
severe engine damage may occur.

! WARNING

Any time service is performed on
a battery, the following must be
observed: Keep sparks, open
flame, cigarettes, or any other
flame away. Always wear safety
glasses. Protect skin and clothing
when handling batteries. When
servicing battery in enclosed
space, keep the area well-venti-
lated. Make sure battery venting
is not obstructed.

! WARNING

Battery posts, terminals, and
related accessories contain lead
and lead compounds, chemicals
known to the state of California to
cause cancer and reproductive
harm. Wash hands after handling.

Содержание S2008ACAAAUSG









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды