manualshive.com logo in svg

Arctic Cat S2008ACAAAUSG, Руководство оператора

Поделиться
Скачать
Arctic Cat S2008ACAAAUSG Скачать руководство пользователя страница 22

18

GENERAL INFORMATION

Charging System 

Warning Icon 

(1100 cc)

The Charging System Warning Icon is

designed to warn the operator if the

battery charging system is not func-

tioning. The icon should illuminate

each time the key is turned to RUN or

START, and it should go out when the

engine starts. If the icon stays illumi-

nated or it illuminates while the

engine is running, the battery is not

being charged, and the snowmobile is

running on battery reserve power only.

If the Charging System Warning Icon

illuminates, you should, as soon as

possible, take the snowmobile to an

authorized Arctic Cat Snowmobile

dealer for service. If not under war-

ranty, this service is at the discretion

and expense of the snowmobile owner.

The engine 

WILL NOT RUN

 with-

out battery power.

Low Oil Warning Icon

The Low Oil Warning Icon is designed

to alert the snowmobile operator when

the oil in the oil injection reservoir

gets below a prescribed level; how-

ever, it is highly recommended that a

visual verification of the oil level in

the reservoir be done prior to operat-

ing the snowmobile. Once the Low Oil

Warning Icon illuminates during oper-

ation of the snowmobile, the operator

must periodically monitor the level of

oil in the reservoir and must fill the

reservoir the next time gasoline is

added to the gas tank. The “alert level”

of the Low Oil Warning Icon is

approximately equal to 1 tankful of

gasoline under normal operating con-

ditions.

Oil Pressure Warning 

Icon (1100 cc)

The Oil Pressure Warning Icon indi-

cates engine oil pressure, not the oil

level; however, if the oil level is low, it

may affect oil pressure. 

The icon should illuminate each time

the ignition switch is turned to RUN

or START, and it should go out when

the engine starts. If the icon illumi-

nates while the engine is running, oil

pressure has been lost and the engine

will automatically shut off. 

If oil pressure is lost, use the following

procedure to check the oil level:

1. With the engine off, remove the

engine oil level stick and wipe it

clean. Without screwing it in, set

the stick back in the oil tank.

Remove it and observe the oil

level on the stick. If the oil level

is at or below the ADD mark on

the oil level stick, add only

enough recommended oil to raise

the level to the NORMAL range.

DO NOT overfill the reservoir

with oil.

Jaguar Z1/TZ1

Steady Flash
(Coolant 
Temperature Icon)

Coolant Tempera-
ture Above 110° C 
(230° F).

Constant On
(Coolant 
Temperature Icon) 

Coolant Tempera-
ture Above 115° C 
(239° F).

! CAUTION

At this point, take precautionary
measures such as changing to
loose snow terrain, shutting the
engine off (allowing the engine to
cool down), and checking coolant
level. If unable to either determine
or remedy the problem, take the
snowmobile to an authorized Arc-
tic Cat Snowmobile dealer for ser-
vice.

! CAUTION

If unable to either determine or
remedy the problem, take the
snowmobile to an authorized Arc-
tic Cat Snowmobile dealer for ser-
vice.

Содержание S2008ACAAAUSG









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды