Arctic Cat S2008ACAAAUSG страница 18 Скачать руководство пользователя

Страница: 18 / 104

GENERAL INFORMATION

1. Check the oil level. If the oil level

is below the lower mark on the oil

level stick, add only enough rec-

ommended oil to raise the level

between the upper and lower

marks. DO NOT overfill the

crankcase with oil.

2. Start the engine. The warning

icon should go out within five

seconds.

If the engine does not start, take the

snowmobile to an authorized Arctic

Cat Snowmobile dealer.

Check Engine Icon

The Check Engine Icon is controlled

by the ECU and may illuminate for a

number of reasons.



NOTE: The icon should illumi-

nate each time the key is turned to
RUN or START, and it should go
out when the engine starts.

If the icon stays illuminated or it illu-

minates while the engine is running,

the ECU is receiving input that is out-

side of its established parameters. If

the Check Engine Icon illuminates,

take the snowmobile to an authorized

Arctic Cat Snowmobile dealer for ser-

vice. If not under warranty, this ser-

vice is at the discretion and expense of

the snowmobile owner.

SPEEDOMETER/

TACHOMETER

INDICATOR ICONS

(Standard Gauge)

This snowmobile is equipped with a

combination speedometer/tachometer.

Indicator icons are incorporated within

the speedometer/tachometer. Also

incorporated into the speedometer/

tachometer is a digital readout screen.

FZ003A

A. Low Oil

B. Coolant Temperature

C. Low Fuel

D. Fuel Level

E. Service

F. High Beam

RPM/MPH (kph)

By pushing the left button once, the

RPM and MPH will be displayed (one

on the readout screen and one with the

needle). By pushing the button once

again, the functions will be reversed.

By pushing the left button (with speed

being displayed) for more than two

seconds, the display will change

between standard mph or metric kph.

Release the button when desired dis-

play appears.

With RPM displayed on the readout

screen by pushing and holding the left

button, maximum RPM will be dis-

played on the readout screen. The

maximum RPM readout will reset

when the right button is pushed (while

maximum RPM is displayed).

Odometer/Trip-Meter

(1)/Trip-Meter (2)/

Hour-Meter/Clock



NOTE: The clock is available on

electric start models only.

Содержание S2008ACAAAUSG









































































































Результаты поиска

Содержание S2008ACAAAUSG

Отзывы:

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

Популярные бренды

Arctic Cat S2008ACAAAUSG, Руководство оператора

Результаты поиска

Содержание S2008ACAAAUSG

Отзывы:

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

Популярные бренды