Arctic Cat S2008ACAAAUSG Скачать руководство пользователя

Страница: 36 / 104

GENERAL INFORMATION

1. Adjust the seat to the lowest posi-

tion; then while lifting on the top

forward part of the seat, remove

the self-tapping screw from the

right side of the seat support

assembly.

741-718A

2. Press in on the left-end of the seat

adjuster lever at the rear storage

compartment; then pull out on the

seat adjuster lever.

3. Lift on the back of the seat and

move it forward and upward to
remove it from the chassis.

To install the seat, use the following

procedure:

1. With the seat adjuster lever pulled

out, slide the front of the seat into

position on the chassis; then with

seat position selected, lower the

rear of the seat onto the rear stor-

age compartment.

2. Press down on the rear of the seat;

then secure the seat by releasing

the seat adjuster lever.

3. With the seat adjusted to the low-

est position, install the self-tap-

ping screw into the right side of

the seat support assembly.

ARCTIC POWER

VALVE (APV) SYSTEM

This RPM controlled servomotor

(servo) actuated system adjusts the

size of the exhaust ports to provide

peak performance throughout the

RPM range.

The system consists of an exhaust

valve assembly mounted to the

exhaust side of each cylinder and con-

nected by adjustable cables to an elec-

tronic servo mounted beneath the

hood.



NOTE: The mounting location of

the servo will vary from model to
model.

739-152F

At low RPM, the exhaust valves are

held in the DOWN position by return

springs. This gives the engine a “low

port” exhaust design calibrated to pro-

vide maximum low RPM power and

improve fuel economy at trail speeds.

! CAUTION

Do not use the adjuster lever to
lift the seat.

! WARNING

Make sure the self-tapping screw
is securely tightened and the seat
is securely locked in place or per-
sonal injury may result.

! CAUTION

The correct engine oil to use is
Arctic Cat Synthetic APV 2-Cycle
Oil (p/n 4639-349). Any substitute
may cause an APV malfunction.

Содержание S2008ACAAAUSG









































































































Результаты поиска

Содержание S2008ACAAAUSG

Отзывы:

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

Популярные бренды

Arctic Cat S2008ACAAAUSG, Руководство оператора

Результаты поиска

Содержание S2008ACAAAUSG

Отзывы:

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

Популярные бренды