Arctic Cat S2008ACAAAUSG Скачать руководство пользователя | Manualshive

Страница: 26 / 104

background image

22

GENERAL INFORMATION

0741-427

2. Adjust the handlebar up or down

and/or rotate the handlebar to

operator’s desired position; then

press down on the cam lever until

the lock pin is properly positioned

and locked. Check steering for

maximum right/left turning capa-

bilities.



NOTE: At this point, gently lift

the cam lever without pressing in
on the lock pin. If the cam lever
cannot be lifted, the lock pin is
secure.



NOTE: Do not rotate the handle-

bar to a position that allows air to
enter the brake system.

3. Test the handlebar to ensure that it

does not rotate within the riser

block. If it does not rotate, pro-

ceed to step 4. If it does rotate,

release the cam lever and rotate

the cam lever clockwise; then

press down on the cam lever until

the lock pin is properly positioned

and locked. Repeat this procedure

until the handlebar is properly

secured.

4. After the handlebar is “locked” in

position, release the cam lever and

rotate it one turn clockwise; then

press down on the cam lever until

it “locks” in place.



NOTE: At this point, gently lift

the cam lever without pressing in
on the lock pin. If the cam lever
cannot be lifted, the lock pin is
secure.

EXHAUST SYSTEM

The exhaust system is designed to

reduce noise and to improve the total

performance of the engine. If any

exhaust system component is removed

from the engine and the engine is run,

severe engine damage will result.

! CAUTION

If at any time the lock pin will not
engage into the locked position,
do NOT operate the snowmobile.
Take the snowmobile to an autho-
rized Arctic Cat dealer for service.

! WARNING

Care must be taken to securely
lock the handlebar cam lever to
prevent unexpected “movement”
of the handlebar during operation
over rough terrain. DO NOT offset
the handlebar so steering (maxi-
mum right/left turning capabili-
ties) are altered or throttle and
brake controls will be affected.

«
...
24
25
26
27
28
...
»

Содержание S2008ACAAAUSG









































































































Отзывы:

Нет отзывов

Похожие инструкции для S2008ACAAAUSG

600 INDY VOYAGEUR

Бренд: Polaris Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды