Arctic Cat S2008ACAAAUSG Скачать руководство пользователя | Manualshive

Страница: 15 / 104

background image

GENERAL INFORMATION

11

LOW OIL WARNING

LIGHT (Standard 2-

Stroke Models)

The Low Oil Warning Light is

designed to alert the snowmobile

operator when the oil in the oil injec-

tion reservoir gets below a prescribed

level; however, it is highly recom-

mended that a visual verification of

the oil level in the reservoir be done

prior to operating the snowmobile.

Once the Low Oil Warning Light illu-

minates during operation of the snow-

mobile, the operator must periodically

monitor the level of oil in the reservoir

and must fill the reservoir the next

time gasoline is added to the gas tank.

The “alert level” of the Low Oil Warn-

ing Light is approximately equal to 1

tankful of gasoline under normal oper-

ating conditions.

LOW OIL PRESSURE

WARNING LIGHT

(Bearcat W/T Non-

Turbo/Panther 660

Models)

The Low Oil Pressure Warning Light

indicates engine oil pressure, not the

oil level; however, if the oil level is

low, it may affect oil pressure. The

light should illuminate each time the

ignition switch is turned to RUN or

START, and it should go out when the

engine starts. If the light illuminates

while the engine is running, oil pres-

sure has been lost and the engine will

automatically shut off.

If oil pressure is lost, use the following

procedure:

1. Check the oil level.



NOTE: To ensure an accurate

reading, the snowmobile should
be on level ground.

2. If the oil level is below the lower

mark on the oil level stick, add

only enough recommended oil to

raise the level between the upper

and lower marks. DO NOT over-

fill the crankcase with oil.

3. After adding oil if the engine

starts, oil pressure should be nor-

mal.

If the engine does not start, take the

snowmobile to an authorized Arctic

Cat Snowmobile dealer.

COOLANT

TEMPERATURE

WARNING LIGHT

(Bearcat W/T Non-

Turbo/Panther 660

Models)

If the coolant temperature is at the

maximum running temperature, the

Coolant Temperature Warning Light

will flash a warning (alert). If the cool-

ant temperature is above the maxi-

mum running temperature, the light

will cease flashing and will remain
constantly illuminated.

! CAUTION

At this point, take precautionary
measures such as changing to
loose snow terrain, shutting the
engine off (allowing the engine to
cool down), and checking coolant
level. If unable to either determine
or remedy the problem, take the
snowmobile to an authorized Arc-
tic Cat Snowmobile dealer for ser-
vice.

«
...
13
14
15
16
17
...
»

Содержание S2008ACAAAUSG









































































































Отзывы:

Нет отзывов

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды