Arctic Cat S2008ACAAAUSG Скачать руководство пользователя

Страница: 94 / 104

PREPARATION FOR STORAGE

9. Plug the exhaust system outlet

with a clean cloth.

10. With the ignition switch in the

OFF position:

A. Disconnect the high tension

leads from the spark plugs;

then remove the plugs, con-

nect them to the leads, and

ground them on the cylinder

heads.

B. Pour 29.5 ml (1 fl oz) of SAE

#30 petroleum-based oil into

each spark plug hole and pull

the recoil starter handle slowly

about 10 times.

C. Install the spark plugs and

connect the high tension leads.

11. On carbureted models, drain the

gas from each carburetor float

chamber.

12. Fill the gas tank to its rated capac-

ity; then add Arctic Cat Fuel Sta-

bilizer (p/n 0436-907) to the gas

tank following directions on the

container for the stabilizer/gaso-

line ratio. Tighten the gas tank

cap securely.

13. On standard chain case models,

drain the chain-case lubricant by

removing the chain-case drain

plug located on the backside of

the chain-case assembly. Remove

the chain-case cover and inspect

chain, sprockets, chain tensioner,

and rollers for wear and the chain

for proper tension. Install the

drain plug, chain-case cover, and

seal; then pour the recommended

amount of Arctic Cat Transmis-

sion Lube (p/n 0636-817) into the

filler hole (see Lubrication sec-

tion).

14. On ACT drive gear case models,

flush the gear case and replace the

lubricant (see Lubrication sec-

tion).

15. Remove the drive belt from the

drive clutch/driven pulley. Lay

the belt on a flat surface or slide it

into a cardboard sleeve to prevent

warping or distortion during stor-

age.

16. Clean and inspect the drive clutch

and driven pulley.

17. Apply light oil to the upper steer-

ing post bushing, ski spindles and

bolts, front and rear pivot bush-

ings of the skid frame, and plung-

ers of the shock absorbers.

18. Lubricate the rear suspension,

spindles, speedometer drive

adapter, and driven shaft support

bearing with a low-temperature

grease.

19. Tighten all nuts, bolts, and cap

screws making sure all calibrated

nuts, bolts, and cap screws are

tightened to specifications. Make

sure all rivets holding the compo-

nents together are tight. Replace

all loose rivets.

! CAUTION

Do not do step 10 on the 4-stroke
models; severe engine damage
could result.

! CAUTION

Never crank the engine over with-
out grounding the spark plugs.
Damage to coils and/or CDI unit
may result.

Содержание S2008ACAAAUSG









































































































Результаты поиска

Содержание S2008ACAAAUSG

Отзывы:

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

Популярные бренды

Arctic Cat S2008ACAAAUSG, Руководство оператора

Результаты поиска

Содержание S2008ACAAAUSG

Отзывы:

Похожие инструкции для S2008ACAAAUSG

Бренды по названию

Популярные бренды