Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя

Страница: 60 / 86

CD591

4. Install the carburetor onto the intake manifold; then

tighten the cap screws securely.

CD592

MD2346

5. Install the air intake boot between the air filter and

the carburetor. Secure with the clamp.

CD589

6. Install the float chamber drain hose and the vent hose

to the carburetor.

7. Install the gas hose onto the carburetor.

CD588

Throttle Cable Free-Play

To adjust the throttle cable free-play, use the following

procedure.

1. Pull back rubber boot to access cable adjustment nut.

KM071A

2. Loosen jam nut to allow cable adjustment nut to be

adjusted.

3. Turn cable adjustment nut clockwise to increase free-

play in the cable. Turn the adjustment nut counter-

clockwise to decrease free-play in the cable.

4. There should be approximately 6 mm (0.25 in.) free-

play in the cable.

5. Tighten the jam nut to secure the adjustment; then

slide the rubber boot back into position.

Engine RPM (Idle)



NOTE: To properly adjust the idle RPM, a tachome-

ter is necessary.

1. Set the brake lever locks. Start the engine and warm

it up to normal operating temperature.

CAUTION

Make sure the engine is fully warm before adjusting the
idle RPM.

Содержание DVX 90/90 UTILITY























































































Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды