Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя

Страница: 30 / 86

7. Remove the camshaft from the cylinder head and

secure the cam chain to prevent it falling into the

crankcase.

YT168A

8. Remove the cam chain guide.

YT112

C. CYLINDER

D. PISTON



NOTE: Steps 1-8 in the preceding sub-section must

precede this procedure.

9. Remove the two cap screws from the left side of the

cylinder head; then remove the cylinder head.

Account for two alignment pins and remove and dis-

card the cylinder head gasket.

YT109B

YT110A

10. Lift the cylinder off the crankcase taking care not to

allow the piston to drop against the crankcase.

Account for the gasket and two alignment pins.

11. Remove the cam chain tensioner pivot bolt; then

remove the chain tensioner.

YT114A

12. Using a needle-nose pliers, remove the circlip secur-

ing the piston pin in the piston; then remove the pis-

ton pin and piston. Take care not to drop the circlip

into the crankcase.

CAUTION

Do not rotate the crankshaft without keeping tension on
the cam chain or engine damage could occur.



AT THIS POINT

To service valves and cylinder head, see Servicing Top-
Side Components sub-section.



AT THIS POINT

To inspect cam chain guide, see Servicing Top-Side
Components sub-section.



AT THIS POINT

To service cylinder, see Servicing Top-Side Compo-
nents sub-section.

CAUTION

When removing the cylinder, be sure to support the pis-
ton to prevent damage to the crankcase and piston.

Содержание DVX 90/90 UTILITY























































































Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды