Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя страница 36

Страница: 36 / 86

CC390D

4. At this point, repeat step 1 and if any measurement

exceeds the limit, the cylinder must be replaced.

Measuring Camshaft Lobe Height

1. Using a micrometer, measure each cam lobe height.

YT129

2. The lobe heights must exceed minimum specifica-

tions.

Inspecting Camshaft Bearing/

Sprocket

1. Inspect the camshaft bearings for roughness during

rotation or signs of discoloration.

YT128

2. Inspect the timing sprocket for excessive wear.

YT127

Installing Top-Side

Components

A. PISTON
B. CYLINDER

1. Lubricate the piston pin, connecting rod, and piston

pin bore with motor oil; then install the piston on the

connecting rod making sure there is a circlip on each

side and the open end of the circlip is directed

upwards or downwards.



NOTE: The piston should be installed so the word

“IN” points upward.

YT161

YT159

2. Place the two alignment pins into position. Place a

new cylinder gasket into position; then place a piston

holder (or suitable substitute) beneath the piston skirt

and square the piston in respect to the crankcase.

Содержание DVX 90/90 UTILITY























































































Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Бренды по названию

Популярные бренды

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Бренды по названию

Популярные бренды