Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя | Manualshive

Страница: 28 / 86

background image

25

5. Remove the air filter housing cover and air filter ele-

ment.

6. Remove the intake boot from the carburetor; then

remove the cap screws securing the air filter housing

to the crankcase and remove the air filter housing

and intake boot.

YT006A

7. Remove the exhaust pipe/muffler assembly and

related mounting hardware; then remove the shift

linkage. Account for a grafoil seal on the exhaust

pipe.

YT008A

YT005A

8. Disconnect the electric choke connector (C), stator

coil connector (B), and starter harness connector (A);

then remove the spark plug cap.

YT010A

9. Remove the gasline hose from the carburetor.

10. Remove the nuts from the one rear and two front

through bolts. Do not remove the bolts at this time.

11. Remove the cooling duct from the front of the V-belt

housing; then disconnect the gear shift position

switch connectors.

12. Remove the cap screws securing the front engine

mounting brackets to the frame; then remove the

through bolts and brackets.

13. Slide the engine/transmission forward sufficiently to

clear the rear mounting brackets; then swing the rear

of the assembly out the left side and remove the

engine/transmission from the frame.

YT014

Top-Side Components



NOTE: For efficiency, it is preferable to remove and

disassemble only those components which need to
be addressed and to service only those components.
The technician should use discretion and sound
judgment.



NOTE: The engine/transmission does not have to

removed from the frame for this procedure.



AT THIS POINT

To service any one specific component, only limited dis-
assembly of components may be necessary. Note the
AT THIS POINT information in each sub-section.

«
...
26
27
28
29
30
...
»

Содержание DVX 90/90 UTILITY























































































Отзывы:

Нет отзывов

Похожие инструкции для DVX 90/90 UTILITY

Бренд: Yamaha Страницы: 59

Бренд: TrailMaster Страницы: 8

Бренд: TrailMaster Страницы: 40

Бренд: TrailMax Страницы: 62

Sportsman 800 EFI

Бренд: Polaris Страницы: 388

Бренд: Stels Страницы: 139

Stockchaser IS12 2017

Бренд: Columbia Страницы: 36

Summit SU5-L-2 2017

Бренд: Columbia Страницы: 40

Бренд: Turbosol Страницы: 84

Бренд: Jayco Страницы: 102

Бренд: Landoll Страницы: 82

Бренд: Taylor-Dunn Страницы: 200

Бренд: Yamaha Страницы: 87

Бренд: MULTIQUIP Страницы: 54

Бренд: Baja motorsports Страницы: 44

MARK 23 (SD18E24A)

Бренд: AMF Страницы: 34

1970 SKI-DADDLER SD15M11 A

Бренд: AMF Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды