Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя

Страница: 40 / 86

3. Remove the V-belt; then remove the movable drive

face (A). Account for a bushing (B) and speed lim-

iter spacer (C).

YT021A

4. Remove the centrifugal clutch housing; then remove

the centrifugal clutch shoe/driven pulley assembly.

YT022

5. Remove the starter reduction gear shield; then

remove the starter countershaft housing. Account for

a thrust washer (A) and countershaft (B).

YT024A



NOTE: The thrust washer and countershaft may

come out with the countershaft housing.

6. Remove the starter one-way nut using Starter One-

Way Clutch Nut Wrench (p/n 0444-191); then install

Starter One-Way Clutch Puller (p/n 0444-188) to the

one-way housing.

YT104

7. Install the push-bolt into the puller; then using two

wrenches as illustrated, tighten the push-bolt until

the one-way clutch is free of the crankshaft.

YT104



NOTE: It may be necessary to strike the head of the

bolt sharply with a hammer after tightening to free the
one-way housing from the crankshaft.

8. Make sure the transmission is in neutral; then

remove the gear position switch noting the orienta-

tion of the drive pin. Account for an O-ring.

YT028

Содержание DVX 90/90 UTILITY























































































Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды