manualshive.com logo in svg

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя страница 72

69

YT198

NOTE: It is not necessary to remove the chain guard

to remove the rear sprocket.

INSTALLING REAR SPROCKET

NOTE: Grease all splines with multi-purpose grease and

inspect all O-rings in the brake hub and sprocket retainer.
O-rings should be replaced whenever disassembled.

1. Position the sprocket into the chain; then slide the

axle with sprocket retainer into the housing from the

right side.

2. Secure the rear sprocket to the sprocket retainer with

three cap screws and blue Loctite #242 and tighten to

20 ft-lb.

YT197A

3. Coat the axle threads with red Loctite #271 and

install one axle nut; then using an appropriate rear

axle nut wrench, tighten the inner axle nut to 86 ft-lb.

NOTE: Compress the left hand brake and engage the

brake lever lock to prevent the rear axle from turning.

TR235

T: Torque wrench reading to be calculated

Ts: Specified torque value (86 ft-lb)

Ls: Tool offset length (center to center)

L: Length of torque wrench (handle pivot to headcenter)

ATV2189

4. Install the outer axle nut and tighten to 86 ft-lb.

5. Adjust the chain.

6. Install the rear wheels/hubs and secure with two flat

washers and castle nuts. Tighten to 58 ft-lb; then

install new cotter pins.

NOTE: If cotter pin hole and notch in castle nut do

not align, tighten the nut until the first notch will align
with the cotter pin hole.

7. Install the rubber hub nut covers and remove the

ATV from the support stand.

Rear Hub/Drive Axle

REMOVING REAR HUB/DRIVE AXLE

1. Secure the ATV on a support stand to elevate the rear

wheels.

2. Remove the cotter pins from the castle nuts on the

rear wheel hubs.

3. Remove the rear wheel hub castle nuts; then slide the

rear wheels and hubs off together. Account for the

washers.

4. Remove the two axle nuts securing the brake hub to

the axle.

L x Ts

= T

L + Ls

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

Содержание DVX 90/90 UTILITY























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды