Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя

Страница: 18 / 86

CD620

5. Place the V-belt cover and one rear brake cable tab

into position; then secure with the eight cap screws.

CD617

6. Tighten the cover cap screws to 7 ft-lb.

7. Install the cooling duct.

8. Place the footrest cover into position and secure it to

the footrest with the Phillips-head cap screws.

Tighten securely.

9. Secure the footrest cover to the front and rear fenders

with the Phillips-head cap screws and four cap

screws. Tighten securely.

Adjusting Shift Linkage

If the ATV jumps out of gear, is difficult to get in gear, or

the neutral and reverse indicator lights do not illuminate,

shift linkage adjustment may be necessary.

1. Shift the transmission into reverse; then remove the

cap screw securing the linkage to the transmission

shift arm.

2. Verify the transmission is in reverse, the ignition

switch is in the ON position, the reverse indicator

light is illuminated, and the shift lever is fully in the

reverse position; then loosen the upper and lower

jam-nuts on the shift linkage and adjust the linkage

to align with the shift arm.

YT005B

3. Install the cap screw securing the linkage to the

lower shift arm. Do not tighten at this time.

4. Shift the transmission into neutral and verify the neu-

tral indicator illuminates; then tighten the jam-nuts

and the linkage cap screw securely.

Troubleshooting Brake

System

Problem: Braking poor

Condition

Remedy

Brake shoe(s) - pad(s)

worn

Lever free-play

excessive

Brake drum(s)

worn

1. Replace brake shoe(s) - pad(s)
2. Adjust free-play
3. Replace brake drum(s)

Problem: Brakes drag

Condition

Remedy

Lever free-play

less than minimum

Brake shoe return spring(s)

loose - sprung

1. Adjust free-play
2. Connect - replace return spring(s)

Содержание DVX 90/90 UTILITY























































































Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды