Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя

Страница: 78 / 86

Suspension

The following suspension system components should be

inspected periodically to ensure proper operation.

A. Shock absorber rods bent, pitted, or damaged.

B. Rubber damper cracked, broken, or missing.

C. Shock absorber body damaged, punctured, or leaking.

D. Shock absorber eyelets broken, bent, or cracked.

E. Shock absorber eyelet bushings worn, deterio-

rated, cracked, or missing.

F. Shock absorber spring broken or sagging.

Shock Absorbers

REMOVING FRONT SHOCK
ABSORBERS

1. Secure the ATV on a support stand to elevate the

wheels and to release the load on the suspension.

2. Remove the cap screw and self-locking nut securing

each front shock absorber to the frame.

MD2131

3. Remove the cap screw and self-locking nut securing

each front shock to the A-arms.

MD2132

4. Remove the front shock absorbers.

REMOVING REAR SHOCK

ABSORBER

1. Secure the ATV on a support stand to elevate the

wheels and to release the load on the suspension.

2. Remove the cap screw securing the rear shock

absorber to the frame.

MD2314

3. Remove the cap screw securing the rear shock

absorber to the swing arm; then remove the rear

shock absorber.

MD2315

4. Compress the shock absorber spring and remove the

spring retainer. Remove the spring and spring pre-

load adjuster.

CLEANING AND INSPECTING

1. Clean all shock absorber components.

2. Inspect each shock rod for nicks, pits, rust, bends,

and oily residue.

3. Inspect all springs, spring retainers, shock rods,

dampers, bushings, shock bodies, and eyelets for

cracks, leaks, and bends.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

! WARNING

Make sure the ATV is solidly supported on the support
stand to avoid injury.

CAUTION

Additional support stands are necessary to support the
rear axle when the shock absorbers are removed or
damage may occur.

Содержание DVX 90/90 UTILITY























































































Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды