manualshive.com logo in svg

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя страница 84

81

CLEANING AND INSPECTING

1. Clean the wheels and hubs with parts-cleaning solvent.

2. Clean the tires with soap and water.

3. Inspect each wheel for cracks, dents, or bends.

4. Inspect each tire for cuts, wear, missing lugs, and leaks.

INSTALLING

1. Install each wheel on its hub.

NOTE: Make sure each wheel is installed on its

proper hub as noted in removing (the “rotation
arrow” must indicate forward direction of rotation).

2. Tighten cap screws to 30 ft-lb.

CHECKING/INFLATING

1. Using an air pressure gauge, measure the air pressure

in each tire. Adjust the air pressure as necessary to

meet the specified inflation pressure.

2. Inspect the tires for damage, wear, or punctures.

NOTE: If repair is needed, follow the instructions

found on the tire repair kit or remove the wheel and
have it repaired professionally.

NOTE: Be sure all tires are the specified size and

have identical tread pattern.

3. Test drive the ATV on a dry, level surface and note

any pulling to the left or right during acceleration,

deceleration, and braking.

NOTE: If pulling is noted, measure the circumfer-

ence of the front and rear tires on the pulling side.
Compare the measurements with the tires on the
opposite side. If pulling is noted during braking only,
check and adjust the brakes as necessary and
recheck operation (see the Periodic Maintenance/
Tune-Up section).

4. Increase the air pressure in the tires with the smallest

circumference measurement until all tires are equal

in circumference.

5. Repeat steps 3-4 as necessary to ensure proper handling.

Troubleshooting

! WARNING

Do not operate the ATV if tire damage exists.

Problem: Suspension too soft

Condition

Remedy

1.

Spring(s)

 weak

2.

Shock absorber

 damaged

1. Replace spring(s)
2. Replace shock absorber

Problem: Suspension too stiff

Condition

Remedy

1.

A-arm bushings

 worn

2.

Shock absorber

 improperly adjusted (rear)

1. Replace bushing
2. Adjust shock spring preload

Problem: Suspension noisy

Condition

Remedy

1.

Cap screws (suspension system)

 loose

2.

A-arm bushings

 worn

1. Tighten cap screws
2. Replace bushings

Problem: Rear wheel oscillation

Condition

Remedy

1.

Rear wheel hub bearings

 worn - loose

2.

Tires

 defective - incorrect

3.

Wheel rim

 distorted

4.

Wheel hub cap screws

 loose

5.

Axle shaft nut

 loose

6.

Rear brake

 adjusted incorrectly

7.

Rear suspension arm-related bushing

 worn

8.

Rear shock absorber

 damaged

9.

Rear suspension arm nut

 loose

1. Replace bearings
2. Replace tires
3. Replace wheel
4. Tighten cap screws
5. Tighten nut
6. Adjust brake
7. Replace bushing
8. Replace shock absorber
9. Tighten nut

Содержание DVX 90/90 UTILITY























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды