Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя

Страница: 25 / 86

MD2452

2. Install the throttle cable into the throttle control

housing; then install the cover and secure with the

screws.

MD2454

KM548A

3. Install the brake cable to the lever assembly.

MD2453

4. Position the left brake lever assembly onto the han-

dlebar and secure with the clamp and two cap

screws. Tighten securely.

KM208A

5. Install the brakeline hose on the master cylinder with

the brakeline hose bolt and two washers. Do not

tighten the bolt at this time.

KM208B

6. Remove the cover from the master cylinder and fill

with DOT 4 brake fluid; then install the cover.

7. Place a suitable container under the master cylinder

and compress the lever slowly. Brake fluid should

flow from the loose connection.

8. Tighten the brakeline hose bolt to 20 ft-lb (from step

5); then check the rear brake operation. The brake

lever should be firm and the rear brake should stop

the wheels.



NOTE: If the brake is not firm, the system must be

bled (see Brake Systems - BLEEDING in Periodic
Maintenance/Tune-Up section).



NOTE: Before installing a handlebar grip, use con-

tact spray or alcohol to clean the inside of the grip
and the handlebar of adhesive residue, oil, or any
other contaminant.

9. Apply a liberal amount of Handlebar Grip Adhesive

to the inside of the grip; then slide the right grip onto

the handlebar. Wipe off any excess adhesive.

10. Tighten the right brake lever assembly Allen-head

screw (from step 1) securely.

Содержание DVX 90/90 UTILITY























































































Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды