Arctic Cat DVX 90/90 UTILITY Скачать руководство пользователя

Страница: 19 / 86

Steering/Frame/Controls

The following steering components should be inspected

periodically to ensure safe and proper operation.

A. Handlebar grips worn, broken, or loose.

B. Handlebar bent, cracked, and an equal and com-

plete full-left and full-right turn capability.

C. Steering post bearing assembly/bearing housing

broken, worn, or binding.

D. Ball joints worn, cracked, or damaged.

E. Tie rods bent or cracked.

F. Knuckles worn, cracked, or damaged.

G. Cotter pins damaged or missing.

The frame and welds should be checked periodically for

damage, bends, cracks, deterioration, broken compo-

nents, and missing components.

Steering Post/Handlebar/

Tie Rods

REMOVING

1. Remove the seat.

2. Remove the control cables from the handlebar; then

route them through the metal loop on the steering

post and out of the way.

MD2430

MD2431

3. Remove the handlebar.

MD2139

4. Disconnect the handlebar switch assembly and brake

switch connectors; then route them through the metal

loop on the steering post and out of the way.

MD2416

5. Remove the cap screws securing the body panel. On

the Utility, remove the front and rear racks.

6. Remove the gas tank cap and lift off the panel.

MD2405

7. Remove the cotter pins; then remove the two inner

tie rod ends from the steering post.

Содержание DVX 90/90 UTILITY























































































Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды

Arctic Cat DVX 90/90 UTILITY, Руководство по обслуживанию

Результаты поиска

Содержание DVX 90/90 UTILITY

Отзывы:

Похожие инструкции для DVX 90/90 UTILITY

Бренды по названию

Популярные бренды